Multifunctional Adhesive Hydrogel for Rapid Cardiac Hemostasis and Antibacterial Protection
Advanced Materials Technologies, EarlyView.A multifunctional polyacrylamide/gelatin/tannic acid hydrogel (PGT) is presented for rapid cardiac hemostasis under wet, dynamic conditions. Surface tannic acid coating enables instantaneous wet adhesion, accelerates coagulation, and confers antibacterial activity within a single platform.
Seoha Kim +5 more
wiley +1 more source
Restoring shoulder function after osteoporotic fracture using a novel double-coil rPMS protocol: A case report with functional and radiological follow-up. [PDF]
Trauma Case RepDi Modica V, Sciarrone GJ.
europepmc +1 more source
In Situ Two‐Dimensional Residual Stress Characterization of Thin Films
Advanced Materials Technologies, EarlyView.An integrated in situ curvature metrology platform combining speckle‐based curvature optical metrology (SCOM) with multi‐beam optical sensors (MOS) enables spatially resolved two‐dimensional curvature mapping of thick sputtered coatings. The SCOM technique provides excellent agreement with MOS while providing an extended measurable curvature range ...
Wai Jue Tan +6 more
wiley +1 more source
Microfabrication of Soft Millirobots Propelled by Low Voltage Electrohydraulic Actuators
Advanced Materials Technologies, EarlyView.Manual layer‐by‐layer assembly is replaced by wafer‐level MEMS batch fabrication for compliant polymer‐based electrohydraulic actuators. The microfabricated devices integrate sacrificially defined microcavities, Parylene‐C‐sealed inlets, and multilayer polymer–metal films.
Shai Shmulevich +2 more
wiley +1 more source
Temperature-Dependent Microstructure Evolution and Superplastic Deformation Behavior of Cold-Deformed Cr4Mo4Ni4V Martensitic Steel: From Continuous to Discontinuous Dynamic Recrystallization. [PDF]
Materials (Basel)Wang J +6 more
europepmc +1 more source
UCST‐Driven Shape Morphing in Digital Light Processing 4D‐Printed Hydrogels
Advanced Materials Technologies, EarlyView.A DLP‐printable UCST hydrogel based on poly(acrylic acid‐co‐acrylamide) enables reversible thermally induced expansion and 4D shape morphing. Rational control of composition, porosity, and multimaterial architecture enables predictable 4D shape morphing through differential swelling and localized actuation, opening new opportunities for high‐resolution
Fato Niang +2 more
wiley +1 more source
Static and Dynamic Compressive Properties of Nano-Al<sub>2</sub>O<sub>3</sub>-Reinforced Epoxy Matrix Composites. [PDF]
Polymers (Basel)Li J, Zhang L, Qiao J.
europepmc +1 more source
Collision‐Resilient Winged Drones Enabled by Tensegrity Structures
Advanced Robotics Research, EarlyView.Based on structures of birds such as the woodpeck, this article presents the collision‐resilient aerial robot, SWIFT. SWIFT leverages tensegrity structures in the fuselage and wings which allow it to undergo large deformations in a crash, without sustaining damage. Experiments show that SWIFT can reduce impact forces by 70% over conventional structures.
Omar Aloui +5 more
wiley +1 more source
Intermediate strain rate constitutive modeling of gradient rolled vanadium-microalloyed pearlitic steel for bridge cables. [PDF]
iScienceHuang S +5 more
europepmc +1 more source
3D Printing of Soft Robotic Systems: Advances in Fabrication Strategies and Future Trends
Advanced Robotics Research, EarlyView.Collectively, this review systematically examines 3D‐printed soft robotics, encompassing material selections, function integration, and manufacturing methodologies. Meanwhile, fabrication strategies are analyzed in order of increasing complexity, highlighting persistent challenges with proposed solutions.
Changjiang Liu +5 more
wiley +1 more source