Results 81 to 90 of about 32,766 (267)

Solid‐State Diffusion and Intermetallic Phase Formation in Roll‐Bonded Mg–Zn Composites With Kirigami‐Patterned Inlay

open access: yesAdvanced Engineering Materials, EarlyView.
Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov   +4 more
wiley   +1 more source

Teaching methods for increasing the participations of students: Innovative dynamics games

open access: yesIntangible Capital, 2013
Purpose: This paper analyses new dynamics as teaching methodologies in the context of   the degrees adapted to the EHEA. The aim of this study is double: to assess whether there is greater involvement in seminars with these new dynamics and to test if ...
Ester Oliveras, Patrícia Crespo
doaj   +1 more source

Karl Popper and the Mechanisms of Hydrogen Embrittlement

open access: yesAdvanced Engineering Materials, EarlyView.
Representation of the beginning of loss of ductility rather than embrittlement. Small concentrations of hydrogen in a diffusible form within iron are well‐established to harm the mechanical integrity of steels. There are theories that attempt to explain the pernicious role of hydrogen.
H. K. D. H. Bhadeshia
wiley   +1 more source

Multimodal Data‐Driven Microstructure Characterization

open access: yesAdvanced Engineering Materials, EarlyView.
A self‐consistent autonomous workflow for EBSP‐based microstructure segmentation by integrating PCA, GMM clustering, and cNMF with information‐theoretic parameter selection, requiring no user input. An optimal ROI size related to characteristic grain size is identified.
Qi Zhang   +4 more
wiley   +1 more source

Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy

open access: yesAdvanced Engineering Materials, EarlyView.
A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang   +10 more
wiley   +1 more source

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

open access: yesAdvanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar   +7 more
wiley   +1 more source

Experimental Characterization and Constitutive Modeling of the Effect of Prior Inelastic Strain on the Viscoplastic Behavior of AD730 at 700 °C

open access: yesAdvanced Engineering Materials, EarlyView.
This study shows that superalloys used in aircraft engine disks become much more prone to deformation at high temperatures if they have been strained during manufacturing. This effect increases with the level of prior strain but eventually reaches a limit.
Fabio Machado Alves da Fonseca   +9 more
wiley   +1 more source

Microstructure Reconstruction in Battery Electrodes Using Machine Learning Based on Low‐Voltage Focused Ion Beam–Scanning Electron Microscopy Tomography Images

open access: yesAdvanced Engineering Materials, EarlyView.
Low‐voltage FIB‐SEM tomography combined with a image preprocessing pipeline improves phase contrast and enables reliable machine‐learning segmentation of conductive networks in lithium‐ion battery electrodes. Structural descriptors are extracted from segmented images, done semimanually and automated, and compared.
Lisa Beran   +6 more
wiley   +1 more source

Home - About - Disclaimer - Privacy