Results 141 to 150 of about 41,583 (295)

Recycling End‐of‐Life Solid Oxide Cell Interconnect Assemblies into Commercial‐Grade AISI 304 Stainless Steels

steel research international, EarlyView.
This study validates a recycling pathway for converting interconnect assemblies from end‐of‐life SOC stacks into commercial‐grade AISI 304 steels. Using scrap‐based steelmaking operations, austenitic cast steels with <4.0% δ‐ferrite are successfully produced.
Jeraldine Lastam, Shine‐Od Mongoljiibuu, Alexander Specht, Daniel Grüner, Dmitry Sergeev, Urs A. Peuker, Michael Müller, Ruth Schwaiger   +7 more
wiley   +1 more source

A Comparative Study of Directed Energy Deposition‐Arc and Casting: Enhancing Mechanical and Thermal Properties of Hot‐Work Tool Steels

steel research international, EarlyView.
The study investigates the influence of DED‐Arc/M versus casting on the microstructure and material properties of X40CrMoV5‐1 (AISI H13) hot‐work tool steel. DED‐Arc/M yields finer microstructures, superior mechanical strength, and ductility, but slightly reduced thermal conductivity.
Ulf Ziesing, Aaron Berger, Hendric Schaefer, Sebastian Weber, Jonathan Lentz   +4 more
wiley   +1 more source

Increasing the Reuse Potential of High‐Strength Steels by Extending the Fatigue Life through Surface Treatments

steel research international, EarlyView.
Surface reconditioning through mechanical and electrochemical polishing is shown to extend the fatigue life of predamaged 42CrMo4 steel by over 12 times. By removing ≈100 μm of surface material, surface‐driven fatigue damage is mitigated. This study introduces a reuse potential metric to evaluate fatigue recovery and support sustainable steel reuse. To
Ayush Shrivastava, Oguz Gulbay, Srinivasa Raghavan Raghuraman, Marion Kreins, Fabian Weber, Peter Starke, Alexander Gramlich, Ulrich Krupp   +7 more
wiley   +1 more source

HWTS 50 Tool Steel Tailored for Laser Powder Bed Fusion: Sliding Wear of Bare Surfaces and Nitriding Response in Comparison with 18Ni300 and AISI H13

steel research international, EarlyView.
This work investigates the wear resistance and nitriding behavior of PBF‐LB/M‐processed Osprey HWTS 50, a lean hot work tool steel. Three heat treatment conditions are compared to conventional wrought H13, H11, and PBF‐LB/M 18Ni300. The study highlights HWTS 50's enhanced nitrogen diffusion, deeper nitriding hardness depth, and comparable or improved ...
Jonathan Hann, Giorgia Lupi, Sylvain Dossin, Riccardo Casati, Mandanà Moshiri, Arne Röttger, Faraz Deirmina   +6 more
wiley   +1 more source

Electron microscopic investigation of photothermal laser printed ZnO nanoarchitectures [PDF]

BIO Web of Conferences
Kraft Kristian, Grünewald Lukas, Quintilla Aina, Müller Erich, Steurer Matthias, Somers Paul, Kraus Steven, Feist Florian, Weinert Bastian, Breitung Ben, Marques Gabriel C., Dehnen Stefanie, Feldmann Claus, Kowollik Christopher Barner, Wegener Martin, Aghassi Jasmin, Eggeler Yolita   +16 more
doaj   +1 more source

In Situ Alloying of H13 Tool Steel With TiC via PBF‐LB/M

steel research international, EarlyView.
H13 tool steel is in situ alloyed with titanium carbides (TiC) in amounts up to 30 wt.%. This approach offers the advantage that the carbides melt only partially during processing, preventing excessive carbon enrichment of the steel matrix. The resulting microstructure consists of coarse, undissolved and fine, reprecipitated carbides, leading to grain ...
Oliver Bürgi, Anke Kaletsch, Christoph Broeckmann   +2 more
wiley   +1 more source

EBSD analysis of twin boundaries of prismatic calcite in oyster shells [PDF]

BIO Web of Conferences
Berent Katarzyna, Nalepka Kinga, Checa Antonio   +2 more
doaj   +1 more source

Microstructure, Defects, and Fatigue Response of High‐Strength Tool Steels

steel research international, EarlyView.
The martensitic tool steel family is designed for use in various working environments where they are subjected to repeatedly high mechanical loads. Despite the continuous upgrade of material´s microstructures through compositional development or processing techniques, defects remain a critical factor for the tool performance by leading to fatigue ...
Katerina Chantziara, Jens Bergström, Dimitrios Nikas, Mikael Thomas Grehk   +3 more
wiley   +1 more source

Two‐Stage Isothermal Transformation of Austenite into Nanobainite in a Chemically Inhomogeneous Medium‐Alloy Steel Containing 0.5 wt% C

steel research international, EarlyView.
The effect of chemical inhomogeneity on the microstructure and properties of nanobainitic steel is investigated. A two‐stage isothermal heat treatment that produced a more uniform microstructure is designed. The first‐stage temperature is higher than the MS of depleted bands; conversely, the second‐stage temperature is lower than the first‐stage ...
Bogdan Garbarz, Jarosław Marcisz, Marek Jelec, Władysław Zalecki, Radosław Rozmus, Zofia Kania‐Pifczyk   +5 more
wiley   +1 more source

Amphibole reaction rims record shear during magma ascent. [PDF]

Nat Commun
Wallace PA, Birnbaum J, De Angelis SH, Mariani E, Larsen J, Kendrick JE, Christopher TE, Cole PD, Lamur A, Lavallée Y.   +9 more
europepmc   +1 more source