Results 151 to 160 of about 2,473,071 (281)

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

open access: yesAdvanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati   +11 more
wiley   +1 more source

Kirigami-actuated reconfigurable topological photonic crystals. [PDF]

open access: yesNat Commun
Liu MD   +5 more
europepmc   +1 more source

Characteristics of edge localized mode in JFT-2M H-mode

open access: yesCharacteristics of edge localized mode in JFT-2M H-mode
JFT-2MのHモードプラズマにおいて観測される周辺振動現象の特性について明らかにした。ELMは周辺電子密度に大きな影響を与えるが、電子温度への影響は、セパラトリック面の近傍を除くと少ないことが、ECE測定より明らかとなった。ELMの起きる実験的条件、制御方法を明らかにし、まとめた。まず、重水素プラズマ中では、一般にELMは起きにくいが、密度が低くなると起きる。また、重水素プラズマに比べ、水素プラズマ中ではELMは起きやすい。このELMは加熱入力を増すことにより制御できる。またプラズマ電流をたち下げることにより抑制でき、たち上げることにより、ELMを生成できることが明らかにされた。ELMのMHD特性を磁気プローブ信号の解析により明らかにした。
openaire   +1 more source

Distinct Microstructural Characteristic Lengths Defining Notch Fatigue Crack Initiation and Propagation, and Defect Tolerance in Advanced Steels

open access: yesAdvanced Engineering Materials, EarlyView.
Schematic representation of modes of microcrack nucleation, growth and temporary arrestment at different boundaries, with the criteria for crack propagation in three scenarios: (1) large notch, (2) defect/small sharp notch, and (3) long crack. This work revisits and integrates results on the fatigue behavior of advanced bainitic steels (in particular ...
Lucia Morales‐Rivas
wiley   +1 more source

Butterfly Wing Membranes' Deformation Study. [PDF]

open access: yesBiomimetics (Basel)
Wang B, Qiu J, Zhang Y, Zheng X, Lu K.
europepmc   +1 more source

Microstructure Modification of Additively Manufactured Mo–9Si–8B by Annealing and Its Effects on High‐Temperature Mechanical Properties

open access: yesAdvanced Engineering Materials, EarlyView.
Postbuild annealing systematically modifies the phase fractions and morphology of EB‐PBF processed Mo–9Si–8B. Quantitative microstructure–property correlations reveal how controlled phase evolution enhances high‐temperature compressive strength and creep resistance.
Christopher Schmidt   +5 more
wiley   +1 more source

Investigation of area-dependent high-power failure of film bulk acoustic resonators. [PDF]

open access: yesMicrosyst Nanoeng
Wei Y   +7 more
europepmc   +1 more source

Controlling Grain Growth in Powder Bed Fusion of Yttria‐Stabilized Zirconia Using Femtosecond Lasers: Challenges and Methodological Insights

open access: yesAdvanced Engineering Materials, EarlyView.
Binder‐free laser powder bed fusion of 8YSZ with a femtosecond laser is used to map process windows linking scan strategy, heat accumulation, and grain growth. Time‐resolved thermography and simulations reveal thermal regimes that enable continuous, vitrified, and fine‐grained 8YSZ surface layers without absorptive additives and demonstrate ...
Markus Kühn   +5 more
wiley   +1 more source

Investigating the Low‐Temperature Phase Stability of the Binary Ta–W System

open access: yesAdvanced Engineering Materials, EarlyView.
Atomistic simulations show that the binary Ta–W system forms ordered intermetallic phases, B2‐TaW and D03‐TaW3, as 0 K ground states. Configurational entropy, however, lowers the free energy of the disordered bcc solid solution, which becomes the stable phase above about 400 K.
Klemens Lechner   +7 more
wiley   +1 more source

Home - About - Disclaimer - Privacy