Results 141 to 150 of about 190,088 (285)

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

Interactions between Molten High‐Silicon Electrical Steels and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
This study examines how several molten high‐silicon electrical steels interact with both conventional and recycled MgO–C refractories. For this, various immersion experiments are conducted. In addition to infiltration, a number of mechanisms are identified and explained that control the corrosion of the refractory material.
Lukas Neubert, Matheus Roberto Bellé, Anton Yehorov, Anhelina Mospan, Till M. J. Stadtmüller, Seetharaman Sridhar, Christos G. Aneziris, Olena Volkova   +7 more
wiley   +1 more source

Zein‐Based Adhesives: Sustainable Extraction and Application in Bioadhesive Technologies

Advanced Engineering Materials, EarlyView.
Zein is extracted from corn gluten meal using a simple and scalable process with high yield (~90%). The resulting protein is applied in bioadhesives modified with Ca2+ and Fe3+ ions, exhibiting substrate‐dependent adhesion. The findings demonstrate competitive bonding performance and highlight the role of ionic interactions in tuning adhesion ...
Paula Bertolino Sanvezzo, Daniela Winsley Valereto Friozi, Vinícius de Oliveira, Marcia Cristina Branciforti   +3 more
wiley   +1 more source

Twisted optical fibres as photonic topological insulators. [PDF]

Nat Photonics
Roberts N, Salter B, Binysh J, Mosley PJ, Souslov A.   +4 more
europepmc   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Topological Advantage for Adsorbate Chemisorption on Conjugated Chains. [PDF]

J Phys Chem Lett
Martinez-Gomez L, Ribeiro RF.
europepmc   +1 more source

Microstructural Evolution and Vacancy Defect Formation in Mn–Mo–Ni RPV Steel Under Low Cycle Fatigue: Insights From EBSD and PALS

Advanced Engineering Materials, EarlyView.
Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar, Dhanadeep Dutta, G. Bharat Reddy   +2 more
wiley   +1 more source

Impact of defects and asymmetry on the acoustic transmission of serial resonators. [PDF]

Sci Rep
El Malki M, Antraoui I, Khettabi A, Bin-Jumah M, Sallah M, Hennache A, El Tokhy MS, Zaky ZA.   +7 more
europepmc   +1 more source

Characterization of Nitinol Produced by Laser Powder Bed Fusion for Mechanical Metamaterial Applications

Advanced Engineering Materials, EarlyView.
Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek, Jakub Hurník, Miroslav Šmíd, Ondřej Zobač, Melanie Todt, Daniel Koutný   +5 more
wiley   +1 more source

Cluster-based DFT modeling of Raman vibrations in tetrahedral GeS₂ and GeSe₂ amorphous chalcogenides. [PDF]

Sci Rep
Halenkovič T, Němec P, Nazabal V.
europepmc   +1 more source