Results 1 to 10 of about 14,025 (217)

Retrofitting to Last: Identifying and Avoiding Retrofitting Errors in Bird Protection Devices

open access: yesПернатые хищники и их охрана
Electrocutions on overhead 6–10 kV electric distribution systems are killing substantial numbers of raptors in Kazakhstan, Russia, and adjacent countries.
James F. Dwyer, Richard E. Harness
doaj   +1 more source

INFLUENCE OF EDM WORN SURFACE OF THE WORKING PART OF STEEL BORON TOOTH TO RESTORE ITS CUTTING ABILITY

open access: yesНаука и техника, 2017
The article is devoted to the experimental evaluation of the efficacy of electrical discharge machining (modification) worn cylindrical working surface of the steel of boron in order to restore its cutting ability.
M. G. KiselevG.   +3 more
doaj   +1 more source

MULTI-RESPONSE OPTIMIZATION OF DIELECTRIC FLUID MIXTURE IN EDM USING GREY RELATIONAL ANALYSIS (GRA) IN TAGUCHI METHOD

open access: yesBarekeng, 2022
In the current study, combining the powder with dielectric fluid in electrical discharge machining (PMEDM) is a very fascinating technological approach.
Veniola Forestryani   +2 more
doaj   +1 more source

Influence of Polarity of Electro Discharge Machine (EDM) on Surface Roughness (SR) and Metal Removal Rate (MRR) of Low Carbon Steel [PDF]

open access: yesEngineering and Technology Journal, 2020
Electro discharge machining (EDM) is one of a thermal process that is used for remove of metal from the workpiece by spark erosion. The work of this machine depends on multiple variables. One of the more influential variants on this machine is the change
Shahd Taqi, Saad Shather
doaj   +1 more source

Análisis de la influencia de las condiciones de proceso sobre el acabado superficial de materiales cerámicos fabricados por electroerosión

open access: yesRevista de Metalurgia, 2004
El mecanizado por electroerosión (en Inglés, Electrical Discharge Machining, EDM) constituye una alternativa emergente frente a otros procesos de fabricación de materiales cerámicos conductores, tales como: mecanizado por láser, mecanizado electroquímico,
I. Puertas-Arbizu, C. J. Luis-Pérez
doaj   +1 more source

Influence of graphene coating in electrical discharge machining with an aluminum electrode

open access: yesJournal of the Mechanical Behavior of Materials, 2023
Since the cost of electrodes in electrical discharge machining (EDM) is usually too high, it leads to a significant increase in the production cost.
Pham Van Dong   +6 more
doaj   +1 more source

Steps towards green manufacturing through EDM process: A review

open access: yesCogent Engineering, 2016
This paper focuses on the current machining process initiatives, carried out by various researchers relevant to the environmental aspects, thereafter predicting EDM performances.
Nishant K. Singh   +3 more
doaj   +1 more source

Energy Distribution Ratio into Micro EDM Electrodes

open access: yesJournal of Advanced Mechanical Design, Systems, and Manufacturing, 2010
Energy distribution ratio into micro EDM electrodes was determined based on the summation between the ratio of energy loss due to heat conduction within electrodes and ratio of energy carried away by debris.
Mohd ZAHIRUDDIN, Masanori KUNIEDA
doaj   +1 more source

Effect of SiC-Cu Electrode on Material Removal Rate, Tool Wear and Surface Roughness in EDM Process [PDF]

open access: yesEngineering and Technology Journal, 2020
Electrical discharge machining (EDM) is one of the most common non-traditional processes for the manufacture of high precision parts and complex shapes. The EDM process depends on the heat energy between the work material and the tool electrode.
Yousif Laibi, Saad Shather
doaj   +1 more source

Study the Effect of the Graphite Powder Mixing Electrical Discharge Machining on Creation of Surface Residual Stresses for AISI D2 Die Steel Using Design of Experiments [PDF]

open access: yesEngineering and Technology Journal, 2015
This paperattempted to study the induced surface residual stressesduethe effect of Electrical discharge machining (EDM) input parameters, (the pulse current,the pulse-on time and the type of electrode).The work includedthe use of two types of electrode ...
Ahmed Naif Al-Khazraji   +2 more
doaj   +1 more source

Home - About - Disclaimer - Privacy