Results 101 to 110 of about 19,475 (267)
Tekuk Torsi Lateral Balok I Kantilever Non Prismatis
Jurnal Teknik Sipil, 2014 Abstrak. Dalam makalah ini disajikan hasil dari suatu studi tentang tekuk torsi lateral elastis balok kantilever dengan penampang I nonprismatis. Bentuk ketidak prismatisan adalah ketinggian badan (web) bervariasi linier sedangkan lebar sayap konstan ...
Paulus Karta Wijaya, Paulina Jacintha
doaj
Lateral Torsional Buckling of Steel Beams Elastically Restrained at the Support Nodes
Applied Sciences, 2019 The study shows the results of theoretical investigations into lateral torsional buckling of bisymmetric I-beams elastically restrained against warping and against rotation in the plane of lateral torsional buckling (i.e., against lateral rotation) at ...
Rafał Piotrowski, Andrzej Szychowski
doaj +1 more source
Advanced Engineering Materials, EarlyView.A distinct semi‐confined inner‐tube chemical vapor deposition geometry enables reproducible, large‐area growth of phase‐pure 2D β′‐In2Se3 from InI + Se precursors. Engineering local vapor transport and optimizing precursor delivery and temperature–time conditions yield uniform continuous films.
Dasun P. W. Guruge +8 more
wiley +1 more source
Simplified expressions for elastic lateral torsional buckling of wooden beams
, 2018 A beam finite element formulation is developed for the elastic lateral torsional buckling analysis of wood beams with rectangular cross-sections. The formulation accounts for moment gradient, load height, and pre-buckling deformation effects.
Doudak, Ghasan +3 more
core +1 more source
Advanced Engineering Materials, EarlyView.Aluminum and nitride coatings are used in industry because they are hard, resist wear, and protect against oxidation. Adding boron can improve friction behavior and other properties. This study tests coatings on surfaces with different finishes. Results show smoother surfaces perform better, while rough ones wear faster, although coatings can reduce ...
Adrián Claver +9 more
wiley +1 more source
Buckling Analysis of Two-Span Continuous Beams with Lateral Elastic Brace under Uniform Load
, 2010 Both total potential energy and buckling equation of two-span continuous beam with lateral elastic brace under uniform load are deduced, based on energy variation method and the principle of minimum potential energy.
Jing Ji +3 more
core +1 more source
, 1963 It is shown that a damper applied to the spherical bearing at the ends of a rotating shaft to damp pitch and yaw motions of the journal bearing can markedly reduce the deflection caused by unbalance near critical speeds.
Samuel Levy
core +1 more source
Advanced Engineering Materials, EarlyView.This study shows that superalloys used in aircraft engine disks become much more prone to deformation at high temperatures if they have been strained during manufacturing. This effect increases with the level of prior strain but eventually reaches a limit.
Fabio Machado Alves da Fonseca +9 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Composite Ti–6Al–4V–epoxy lattice structures are additively manufactured and epoxy infiltrated for cyclic loading. At low lattice volume fractions, hybridization produces synergistic gains in stiffness and energy dissipation. At higher volume fractions, synergy diminishes, although composites still exceed metallic lattices in specific energy ...
Joey Tallon +3 more
wiley +1 more source
Limitations on linear elastic procedures in performance assessment of regular frames
, 2015 Linear elastic analysis procedures are employed exclusively in the traditional seismic design of new structures and widely employed in the seismic assessment of existing structures. It is also a convenient tool for the initial checking of deformations in
Ozcamur, Ugurcan, Sucuoğlu, Haluk
core +1 more source