Results 71 to 80 of about 72,584 (265)
An Elimination of Resonance in Electric Drives
Advances in Electrical and Electronic Engineering, 2011 Flexible couplings together with resonance phenomenon are present mainly in the field of servodrives where high accuracy and dynamic requirements are crucial. When dynamics doesn’t correlate with mechanical system design, unwanted frequencies in the system are exited.
Málek, Michal +2 more
openaire +3 more sources
Advanced Engineering Materials, EarlyView.A two‐dimensional multiscale finite element analysis framework was established for the first‐generation MoSiBTiC alloy, and the mechanical and fracture‐related parameters of the constituent phases were calibrated through experiments and simulations. The framework provides a basis for analyzing crack propagation behavior in its complex microstructure ...
Junfeng Du +4 more
wiley +1 more source
On-Site Calibration of an Electric Drive: A Case Study Using a Multiphase System. [PDF]
Sensors (Basel), 2023 Soto-Marchena D +4 more
europepmc +1 more source
Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys
Advanced Engineering Materials, EarlyView.Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak +3 more
wiley +1 more source
Observability of Sensorless Electric Drives
CoRR, 2016 Electric drives control without shaft sensors has been an active research topic for almost three decades. It consists of estimating the rotor speed and/or position from the currents and voltages measurement. This paper deals with the observability conditions of electric drives in view of sensorless control.
Mohamad Koteich +3 more
openaire +2 more sources
Advanced Engineering Materials, EarlyView.The temperature dependence of fatigue behavior in nickel‐based superalloys is investigated through high‐resolution measurements of plastic localization. While increasing temperature reduces localization and enhances fatigue performance in René 88DT, Inconel 718 exhibits a sharp degradation at intermediate temperature due to intensified slip ...
M. Calvat +5 more
wiley +1 more source
Tailoring Functional Properties of Ti–Ni–Cu Shape Memory Alloy Thin Films for MEMS Actuators
Advanced Engineering Materials, EarlyView.A comprehensive study of critical parameters required to develop well‐performing Ti–Ni–Cu thin film shape memory alloy microactuators is provided. Materials science and device integration aspects are integrated by addressing structural and physical relationships using complementary characterization techniques as well as a practical fabrication solution
Elaheh Akbarnejad +6 more
wiley +1 more source
Influence of the Bearing Thermal Deformation on Nonlinear Dynamic Characteristics of an Electric Drive Helical Gear System. [PDF]
Sensors (Basel), 2021 Liu X, Liu D, Hu X.
europepmc +1 more source
Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy
Advanced Engineering Materials, EarlyView.A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang +10 more
wiley +1 more source
An effective range estimation and state-of-charge to mitigate range anxiety in electric vehicles
HeliyonThis article presents a performance investigation of the range and state of electric charge vehicles based on different drive cycles and analyzed. Range anxiety is the major concern in electric vehicles globally.
Shana Lakshmi Prasad, Abhishek Gudipalli
doaj +1 more source