Results 61 to 70 of about 406,303 (299)
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Handbook of Establishing and Maintaining Oxygen‐Free Atmospheres
Advanced Engineering Materials, EarlyView.This study presents a practical framework for creating oxygen‐free atmospheres at ambient pressure using silane‐doped inert gases. The results show that ultra‐low oxygen levels and strongly reduced water content can be achieved through controlled silane dosing, drying systems, and sensor monitoring.
Sascha Jan Zimmermann +3 more
wiley +1 more source
Three-phase modular permanent magnet brushless machine for torque boosting on a downsized ICE vehicle [PDF]
, 2005 The paper describes a relatively new topology of 3-phase permanent magnet (PM) brushless machine, which offers a number of significant advantages over conventional PM brushless machines for automotive applications, such as electrical torque boosting at ...
Howe, D., Wang, J.B., Xia, Z.P.
core +1 more source
Advanced Engineering Materials, EarlyView.Trace additions of Sn and Sr combined with a two‐step aging treatment are shown to enhance the microstructure and performance of Al–Zr–Sc conductor alloys. Strength and electrical conductivity increase concurrently through accelerated precipitation of fine Al3(Sc, Zr) precipitates and improved dislocation resistance, offering a cost‐effective pathway ...
Quan Shao +3 more
wiley +1 more source
Computationally Efficient Strand Eddy Current Loss Calculation in Electric Machines [PDF]
, 2019 A fast finite element (FE) based method for the calculation of eddy current losses in the stator windings of randomly wound electric machines is presented in this paper.
Chong, Yew Chuan +5 more
core +1 more source
On the variation with flux and frequency of the core loss coefficients in electrical machines [PDF]
, 2006 A model of core losses, in which the hysteresis coefficients are variable with the frequency and induction (flux density) and the eddy-current and excess loss coefficients are variable only with the induction, is proposed. A procedure for identifying the
Dellinger, S.J. +5 more
core +1 more source
Advanced Engineering Materials, EarlyView.Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios +5 more
wiley +1 more source
Simulation of electric machines [PDF]
, 2012 Tato bakalářská práce se zabývá modelováním a simulací stejnosměrných a střídavých strojů. Byly vytvořeny celkem čtyři matematické modely. Tři modely stejnosměrných motorů při různém typu buzení (kompaundní, sériový, cize buzený) a jeden model pro motor ...
Klíma, Jiří
core
Методичні вказівки до лабораторних робіт по дисципліні "Електричні машини" [PDF]
, 2019 The edition is dedicated to expand the theoretical knowledge of foreign students on the "Electrical machines" discipline. The objects of study are transformers and electric machines, which are the basis of electric power in various industries.
Duniev, O. O. +3 more
core +1 more source