Results 41 to 50 of about 21,002 (262)
Energies, 2022 The article presents the analysis of operational parameters and thermal analysis of the wheel hub motor during operation in the car drive. The authors proposed an analysis of the operation of the wheel hub motor mounted in a hybrid car, during Artemis ...
Piotr Dukalski, Jan Mikoś, Roman Krok
doaj +1 more source
Annals of Clinical and Translational Neurology, EarlyView.ABSTRACT Objectives Focal cortical dysplasia (FCD) is the most common etiology of drug‐resistant epilepsy in children. Focal to bilateral tonic–clonic seizures (FBTCS) mark a high risk of drug‐resistant epilepsy and involve thalamocortical circuitry in their generation and propagation.
Hua Xie +8 more
wiley +1 more source
A Q‐Learning Algorithm to Solve the Two‐Player Zero‐Sum Game Problem for Nonlinear Systems
International Journal of Adaptive Control and Signal Processing, Volume 39, Issue 3, Page 566-581, March 2025.A Q‐learning algorithm to solve the two‐player zero‐sum game problem for nonlinear systems. ABSTRACT This paper deals with the two‐player zero‐sum game problem, which is a bounded L2$$ {L}_2 $$‐gain robust control problem. Finding an analytical solution to the complex Hamilton‐Jacobi‐Issacs (HJI) equation is a challenging task.
Afreen Islam +2 more
wiley +1 more source
IET Electric Power ApplicationsThis paper proposes an optimal voltage compensation method for the drop across long power cable in a motor drive system. In the proposed method the drive is utilised to compensate the voltage drop and no additional voltage regulation device is required ...
Mesaad Albader +2 more
doaj +1 more source
Simple Design Scheme for a 300 kW Modular NPC Inverter Using Thermal RC Network Analysis
EnergiesThis paper proposes a simple design scheme for a modular NPC inverter using thermal RC network analysis. The proposed design process is an efficient and straightforward approach to designing the heatsink for a 300 kW modular neutral-point-clamped ...
Jae-Woon Lee +4 more
doaj +1 more source
Looper and tension control in hot strip finishing mills based on different control approaches
Journal of Engineering and Applied Science, 2022 The looper control of hot strip finishing mill is one of the most critical control items in hot strip rolling mill process. It is a highly complex nonlinear system, with strong states coupling and uncertainty that present a difficult control challenge ...
Ahmed Gaber +2 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study presents a reversible temperature sensor with high switching ratio, ∼103. The device is fabricated using PET‐ITO and carbon nanotube dispersions in alkane. Considering its application in cold chain logistics, a proof‐of‐concept with LED is showcased. Thus, a temperature drop below the threshold temperature (crystallization temperature of the
Sunil Kumar Behera +8 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study presents an infrared monitoring approach for direct laser interference patterning (DLIP) combined with a convolutional neural network (CNN). Thermal emission data captured during structuring are used to predict surface topography parameters.
Lukas Olawsky +5 more
wiley +1 more source