Results 61 to 70 of about 220,265 (355)
Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys
Advanced Engineering Materials, EarlyView.Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak +3 more
wiley +1 more source
Electrical Discharge Machined Surface of the Insulating ZrO2 Ceramics
Journal of Advanced Mechanical Design, Systems, and Manufacturing, 2011 Several insulating ceramic materials have been machined by electrical discharge machining (EDM) using the assisting electrode method that has been proposed by the authors' group.
Daiki HANAOKA +2 more
doaj +1 more source
Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites
Advanced Engineering Materials, EarlyView.Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter +9 more
wiley +1 more source
Nonconventional Technologies Review, 2015 Electrical discharge machining (EDM) is one of the most used non-traditional machining processes. In order to detach and remove the material from the workpiece surfaces, the process uses thermoelectric energy that allows the development of electrical ...
Irina Besliu, Margareta Coteata
doaj
EXPERIMENTAL EVALUATION OF WEDM MACHINED SURFACE WAVINESS
Acta Polytechnica, 2016 Wire Electrical Discharge Machining (WEDM) an unconventional machining technology which has become indispensable in many industries. The typical morphology of a surface machined using the electrical discharge technology is characterized with a large ...
Katerina Mouralova +2 more
doaj +1 more source
Method of producing a plug-type heat flux gauge [PDF]
, 1992 A method of making a plug-type heat flux gauge in a material specimen in which a thermoplug is integrally formed in the specimen is disclosed. The thermoplug and concentric annulus are formed in the material specimen by electrical discharge machining and
Koch, John, Jr., Liebert, Curt H.
core +1 more source
Advanced Engineering Materials, EarlyView.This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley +1 more source
Advances in Mechanical Engineering, 2017 The mechanism of surface topography formation of Inconel 718 in low-speed wire electrical discharge machining was studied, and its on-line prediction based on acoustic emission detection technology is carried out.
Yan Wang, Duxing He, Lin Yang, Wei Xiong
doaj +1 more source
Mathematics, 2020 Technological tables are very important in electrical discharge machining to determine optimal operating conditions for process variables, such as material removal rate or electrode wear.
C. J. Luis Pérez
doaj +1 more source
Design of an electrochemical micromachining machine [PDF]
, 2014 Electrochemical micromachining (μECM) is a non-conventional machining process based on the phenomenon of electrolysis. μECM became an attractive area of research due to the fact that this process does not create any defective layer after machining and ...
A Muetze +40 more
core +1 more source