Results 81 to 90 of about 6,209,447 (296)

Thermal model of crater formation process in electrical discharge machining

Case Studies in Thermal Engineering
The formation mechanism of the discharge crater in electrical discharge machining process is not fully understood, which affects the application of electrical discharge machining technology.
Baocheng Xie, Jinting Hou, Boxiong Dong, Chenhao Xu, Rongzheng Yao, Yuan Zhang   +5 more
doaj   +1 more source

Wire Electrical Discharge Machining Property of Magnesium [PDF]

, 2008
Pure Magnesium was cut by Wire Electrical Discharge Machining, and its machining properties were compared with Aluminum base alloy. Moreover, the open voltage, the peak current, the average processing voltage and the off time were changed respectively to
金子, 健正, KANEKO, Kensei, YAMADA, Ryuichi, 山田, 隆一   +3 more
core  

Nitride MXenes Beyond Carbides: Bridging the Gap Between Computational Prediction and Experimental Realization

Advanced Functional Materials, EarlyView.
Nitride MXenes remain constrained by a persistent gap between computational prediction and experimental realization. This Review identifies the thermodynamic, kinetic, and chemical barriers limiting their synthesis, critically evaluates emerging fabrication routes, and proposes a multidimensional computational‐experimental framework to accelerate the ...
Naresh Varnakavi, Masoud Soroush
wiley   +1 more source

Defect‐Free Transfer Principles for Scalable, Thin Garnet‐Based Hybrid Solid Electrolytes in Solid‐State Batteries

Advanced Functional Materials, EarlyView.
Defect‐free transfer principles enable scalable fabrication of 15 µm‐thin garnet‐based hybrid solid electrolytes. Hansen solubility parameters correlate interfacial compatibility with coating, transfer, and impregnation behavior, guiding rational selection of slurry/substrate, binder/substrate, and binder/polymer electrolyte combinations.
Seul Gi Chu, Myeong Hwan Lee, Jungdon Suk, Seung‐Wan Song, Hye Min Ryu, Halim Kang, Jusung Han, Myung‐Soo Park, Yongku Kang   +8 more
wiley   +1 more source

DEVICE FOR THREADING BY ELECTRTICAL DISCHARGE

Nonconventional Technologies Review, 2016
There are situations when for distinct reasons, a process of threading by electrical discharge machining has to be applied. In order to materialize an electrical discharge threading process, an analysis of the information available in the specialty ...
Ionel Coman, Laurentiu Slatineanu, Margareta Coteata, Oana Dodun, Gheorghe Nagit, Irina Besliu   +5 more
doaj  

Beyond Thin Film Limits—Superhard and Hydrogen‐Free Amorphous Carbon Coatings With Over 100 µm Thickness

Advanced Functional Materials, EarlyView.
For the first time, an extreme‐thick laser‐arc PVD ta‐C (DLC) coating exceeding 100 µm is demonstrated, opening up new possibilities for ultra‐high load bearing capacity. This superhard amorphous carbon architecture combines >50% sp3 bonding, robust adhesion and self‐supporting performance, shielding substrates from plastic flow under extreme contact ...
Martin Zawischa, Frank Kaulfuß, Stefan Makowski, Volker Weihnacht   +3 more
wiley   +1 more source

Ferroelectric Quantum Dots for Retinomorphic In‐Sensor Computing

Advanced Materials, EarlyView.
This work has provided a protocol for fabricating retinomorphic phototransistors by integrating ferroelectric ligands with quantum dots. The resulting device combines ferroelectricity, optical responsiveness, and low‐power operation to enable adaptive signal amplification and high recognition accuracy under low‐light conditions, while supporting ...
Tingyu Long, Huanyu Zhou, Jaewan Ko, Hongwei Tan, Jaemin Lim, Yanfei Zhao, Daehan Kang, Eojin Yoon, Gyeong‐Tak Go, Somin Kim, Seung‐Woo Lee, Chan‐Yul Park, Hyojun Choi, Hyeran Kim, Hyung Joong Yun, Sung Hyuk Park, Kwan Sik Park, Jeong Woo Park, Mungeun Kim, Yong Soo Cho, Ho Won Jang, Wenqiang Yang, Min Hyuk Park, Wan Ki Bae, Sebastiaan van Dijken, Joona Bang, Tae‐Woo Lee   +26 more
wiley   +1 more source

Neuromorphic Electronics for Intelligence Everywhere: Emerging Devices, Flexible Platforms, and Scalable System Architectures

Advanced Materials, EarlyView.
The perspective presents an integrated view of neuromorphic technologies, from device physics to real‐time applicability, while highlighting the necessity of full‐stack co‐optimization. By outlining practical hardware‐level strategies to exploit device behavior and mitigate non‐idealities, it shows pathways for building efficient, scalable, and ...
Kapil Bhardwaj, Roshni Satheesh Babu, Yuxin Xia, Eva Bestelink, Radu Sporea, Nikos Hastas, Ioannis Zeimpekis, Dimitra G. Georgiadou, Sayani Majumdar   +8 more
wiley   +1 more source

Study on Electric-Discharge Machining

Journal of The Japan Society of Electrical Machining Engineers, 1968
Hisao KURAFUJI, Yoshitsugu MUKOYAMA
  +6 more sources

Micro-EDM Pulse Energy Distribution Ratio Determination [PDF]

, 2013
In this paper, a pulse energy distribution ratio determination method for micro-EDM is presented. The pulse energy distribution ratio is a crucial parameter in the modeling of the EDM process. Instead of measuring the electrode temperature variation
Rajurkar, Kamlakar, Shao, Bai
core