Results 121 to 130 of about 2,112,617 (302)
Near‐Field Electrospinning Micro‐Printhead Achieves Precise Control of Nanofiber Deposition
Advanced Engineering Materials, EarlyView.A micro‐printhead for near‐field electrospinning enables reproducible deposition of polymer nanofibers with diameters below 50 nm. Systematic parameter studies uncover the mechanisms linking operating conditions to fiber morphology, paving the way for precise and low‐cost nanoscale 3D manufacturing.As a high‐resolution, cost‐effective, and rapid ...
Han Xu, Dario Mager, Jan G. Korvink
wiley +1 more source
Nonconventional Technologies Review, 2015 In the first part of this article, the authors make a short presentation of electrode tool displacement control system for sinker electrical discharge machining. The advantages of stepper motor used in kinematics chain are also mentioned.
Emanoil Toma, Carmen Simion
doaj
Advanced Engineering Materials, EarlyView.This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.ZnS‐MXene‐TiO2 nanocomposite heterojunction for photocatalytic decomposition of this methylene blue dye (MB) greatly improves light absorption, charge separation, and active site area. Two‐dimensional MXene forms nanocomposites by easily combining them with 0D (quantum dots), 1D (tube and wire), 2D (plane and sheet), and 3D (particle and lamellar ...
Latiful Kabir +7 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff +9 more
wiley +1 more source
Gong-kuang zidonghua, 2011 The paper introduced application range, mechanical part, electrical control part, main functions and actual application of MG110/130-TPD model electrical haulage in-web shearer on a working face of ultra-thin coal seam with large inclination.
FENG Chun +4 more
doaj
Surface electrical properties experiment. Part 2: Theory of radio-frequency interferometry in geophysical subsurface probing [PDF]
The radiation fields due to a horizontal electric dipole laid on the surface of a stratified medium were calculated using a geometrical optics approximation, a modal approach, and direct numerical integration.
Kong, J. A., Tsang, L.
core +1 more source
Advanced Engineering Materials, EarlyView.The wettability of aluminum droplets (Al) on different copper substrates (Cu), where liquid Al spreads on solid Cu surfaces to form a liquid–solid interface, is studied numerically and experimentally. The experimental and numerical results show good agreement in the fast‐spreading regime.
Shan Lyu +8 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Through direct application of porous transport layer (PTL) on the bipolar plate (BPP) with thermal spraying, the interfacial contact resistance is improved. With the cold gas sprayed BPP–PTL coating system, a proton exchange membrane water electrolysis cell with a cell voltage of Ucell = 1.9 V can be operated up to i = 2.5 A/cm2 in a dynamic mode ...
Kirsten Bobzin +5 more
wiley +1 more source