Results 71 to 80 of about 11,280,876 (284)
Advanced Engineering Materials, Volume 27, Issue 6, March 2025.ErB4 and NdB4 nanostructured powders are produced by mechanochemical synthesis. 5 h mechanical alloying and 4 M HCl acid leaching are used in the production. ErB4 and NdB4 powders exhibit maximum magnetization of 0.4726 emu g−1 accompanied with an antiferromagnetic‐to‐paramagnetic phase transition at about TN = 18 K and 0.132 emu g−1 with a maximum at ...
Burçak Boztemur +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios +5 more
wiley +1 more source
Electrical properties of various single-wall carbon nanotube networks [PDF]
, 2010 This thesis investigates conduction mechanisms of covalently and non covalently functionalised single wall carbon nanotube (SWCNT) networks. Unlike previous strategies where diamines were used, a novel route to covalently bridge SWCNTs by organic ...
Jombert, Alice Stécy +1 more
core
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
Heterogeneity in relation to electrical and mineralogical properties of hematitic sandstone samples
Applied Water Science, 2020 Electrical properties of mixtures of composite materials are sensitive to texture between grains. Electrical measurements of hematite and sandstone composite mixture were performed in the frequency range (5 × 10−4 Hz–105 Hz).
Mohamed Mahmoud Gomaa
doaj +1 more source
Advanced Engineering Materials, EarlyView.This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Low‐temperature imidization of PEG‐modified polyimide enables fully screen‐printed, roll‐to‐roll fabrication of flexible electrodes on PET substrates, delivering robust mechanical durability and reliable ECG/EMG signal performance for wearable electronics.
Akib Abdullah Khan, Jong‐Hoon Kim
wiley +1 more source
Advanced Engineering Materials, EarlyView.A unified research data management framework for heterogeneous materials data is presented. The system integrates multimodal datasets using ontologies and knowledge graphs, enabling interoperability and FAIR (findable, accessible, interoperable, reusable) data principles. By linking data across scales and workflows, it supports reproducible, Artifitial
Doaa Mohamed +6 more
wiley +1 more source
Investigations of Electrical Trees in the Inner Layer of XLPE Cable Insulation Using Computer-aided Image Recording Monitoring [PDF]
, 2010 Using a computer-aided image recording monitoring system, extensive measurements have been performed in the inner layer of 66 kV cross-linked polyethylene (XLPE)cables.
Li, Shengtao +7 more
core +1 more source
Advanced Engineering Materials, EarlyView.Copper‐based composites enhanced with carbon feature convenient mechanical properties and favorable electric conductivity. Processing via deformation and thermomechanical treatments can introduce advantageous microstructures further enhancing their performance. Herein, copper–graphene powder‐based composites are directly consolidated via rotary swaging
Radim Kocich +3 more
wiley +1 more source