Results 71 to 80 of about 171,869 (269)

ON THE QUANTITY OF ELECTRICITY AND THE ENERGY IN ELECTRICAL STIMULATION [PDF]

Journal of General Physiology, 1936
Weiss's and Hoorweg's laws are discussed with respect to the dynamics of the excitatory process. The former is shown to have a simple basis which is inadequate, however, because it implies a constant rate of subsidence of the state of excitation. Hoorweg's law does not follow logically from the same basis so the two laws do not represent the same ...
openaire   +2 more sources

Parameter Variation in Planetary Ball Milling of Titanium Aluminide Powder in XHV‐Adequate Atmosphere

Advanced Engineering Materials, EarlyView.
This study investigates the effects of milling parameters, including rotational speed, milling duration, and ball‐to‐powder ratio, on TiAl particle size and morphology in an XHV‐equivalent atmosphere. The creation of oxide‐free surfaces enhances the mechanical properties of green bodies.
Jytte Möckelmann, Armin Piwek, Julius Peddinghaus, Kai Brunotte, Bernd-Arno Behrens   +4 more
wiley   +1 more source

Current Status and Challenges in Data Collection for Aerospace Coatings Deposited by Plasma Spraying

Advanced Engineering Materials, EarlyView.
An innovative approach has been integrated into the GRENAT project to optimize plasma spraying and coating performance. Raw materials are accelerated and melted in the plasma generated by torches, creating coatings. Monitoring sensors collect process data which are combined with ex situ characterization data.
Lila Randriamananjara, Vincent Rat, Quentin Dubreuil, Patrice Valorge, Simon Goutier, Alain Denoirjean, Olivier Messe, Céline Ruelle, Jean‐Philippe Poli   +8 more
wiley   +1 more source

Evaluation of Plasticity and Creep Parameters From Tensile Stress–Strain Data for a Range of Strain Rates

Advanced Engineering Materials, EarlyView.
This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley   +1 more source

Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants

Advanced Engineering Materials, EarlyView.
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir, Jixing Lin, Yuncang Li, Li Zhu, Paul F. A. Wright, Cuie Wen   +5 more
wiley   +1 more source

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

Advanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar, Akash Vyas, Mohammad Aatif Qazi, Nashit Jalal, Maria Ophelia Jarligo, Mostafa Yakout, Jing Liu, André McDonald   +7 more
wiley   +1 more source

Enhancing Bubble Removal in Geometry‐Optimized Electrodes

Advanced Engineering Materials, EarlyView.
3D‐printed lattice electrodes outperform stochastic foams in alkaline water electrolysis despite 20%–25% lower surface area. Straight flow channels generate Venturi‐like bubble entrainment, suppressing gas accumulation that renders foam interiors electrochemically inactive.
Florian Wiesner, Peter Förster, Alexander Limper, Anselm Brodersen, Matthias Wessling, John Linkhorst   +5 more
wiley   +1 more source

Microstructure Reconstruction in Battery Electrodes Using Machine Learning Based on Low‐Voltage Focused Ion Beam–Scanning Electron Microscopy Tomography Images

Advanced Engineering Materials, EarlyView.
Low‐voltage FIB‐SEM tomography combined with a image preprocessing pipeline improves phase contrast and enables reliable machine‐learning segmentation of conductive networks in lithium‐ion battery electrodes. Structural descriptors are extracted from segmented images, done semimanually and automated, and compared.
Lisa Beran, Vincent Nebel, Dominik Perius, Kshitij Kumar, Yannis Heim, Laura Bies, Tobias Kraus   +6 more
wiley   +1 more source

Innovative Approaches in Residential Solar Electricity: Forecasting and Fault Detection Using Machine Learning

Electricity
Recent advancements in residential solar electricity have revolutionized sustainable development. This paper introduces a methodology leveraging machine learning to forecast solar panels’ power output based on weather and air pollution parameters, along ...
Shruti Kalra, Ruby Beniwal, Vinay Singh, Narendra Singh Beniwal   +3 more
doaj   +1 more source

Designing Polymer Nanocomposites for X‐Ray Shielding: Mechanisms, Architectures, and Scalable Processing

Advanced Engineering Materials, EarlyView.
This review highlights advances in lightweight, lead‐free polymer nanocomposites for diagnostic X‐ray shielding. By linking filler chemistry, dispersion, architecture, and photon interaction mechanisms, it establishes structure–performance relationships guiding material design.
Aklilu G. Messele, Hossein Ipakchi, Tizazu H. Mekonnen   +2 more
wiley   +1 more source