Results 21 to 30 of about 707,090 (200)

Electrochemical micromachining: An introduction

Advances in Mechanical Engineering, 2016
Electrochemical machining is a relatively new technique, only being introduced as a commercial technique within the last 70 years. A lot of research was conducted in the 1960s and 1970s, but research on electrical discharge machining around the same time
Rebecca J Leese, Atanas Ivanov
doaj   +1 more source

Study on Kerosene-submerged Jet Electrochemical Machining and Optimization of the Electrochemical Machining Parameters

International Journal of Electrochemical Science, 2021
Kerosene-submerged jet electrochemical machining (Jet-ECM) has been proven to be an effective process to enhance the machining localization of Jet-ECM.
Xinchao Li, Pingmei Ming, Xinmin Zhang, Shen Niu, Xingshuai Zheng, Liang Yan, Wei Wang, Yunyan Zhang   +7 more
doaj   +1 more source

Effect of electro discharge machining (EDM) on the AISI316L SS white layer microstructure and corrosion resistance [PDF]

, 2013
The localised corrosion resistance of austenitic stainless steels is strongly influenced by the quality of finished surface. EDM machining induces substantial changes by the high thermal gradients generated by electric sparks.
SIDHOM, Habib, GONZALEZ, Gonzalo, AMADOU, Tidiane, GHANEM, Farhat, BRAHAM, Chedly   +4 more
core   +1 more source

Progress in Non-Traditional Processing for Fabricating Superhydrophobic Surfaces

Micromachines, 2021
When the water droplets are on some superhydrophobic surfaces, the surface only needs to be inclined at a very small angle to make the water droplets roll off.
Dili Shen, Wuyi Ming, Xinggui Ren, Zhuobin Xie, Xuewen Liu   +4 more
doaj   +1 more source

Mechanism of electrical discharge and electrochemical hybrid sinking machining using water-in-oil nanoemulsion: processing phenomena and multiphysics simulation [PDF]

AIP Advances
Electrical discharge and electrochemical hybrid sinking machining (EDCSM) using a water-in-oil (W/O) nanoemulsion demonstrates high-quality machined surface and good machining accuracy. However, the specific machining mechanism of this technology remains
Yutian Xia, Yubin Cai, Ning Du, Hang Dong, Qingsong Zhang, Yuan Guo, Jianping Zhou   +6 more
doaj   +1 more source

Electrochemical drilling and multi response optimization using different methods of assigning weights to the responses for sustainable machining of AA6061-TiB2 in-situ composites [PDF]

Songklanakarin Journal of Science and Technology (SJST), 2021
The current paper describes the multiple response optimization of electrochemical machining (ECM) responses, such as specific energy consumption (SEC), overcut, and material removal rate (MRR), aimed at sustainable machining.
S. Chandrasekhar, N. B. V. Prasad
doaj   +1 more source

Clarification of gap phenomena in precise electrochemical machining by implementing a "virtual sensor"

, 2022
S.16-22Gap phenomena in precise electrochemical machining (PECM) have been scarcely investigated. State-of-the-art measurement technology does not allow the recording of temperature, gas evolution and electrical conductivity on the time scale of the ...
Klocke, Fritz, Zeis, Markus, Klink, Andreas, Heidemanns, Lukas   +3 more
core   +1 more source

Distribution Manner of Compaction Circular Cylinders in Through-Active-Mask Electrochemical Machining

Advances in Mechanical Engineering, 2015
Electrochemical machining is widely used in the processing of difficult-to-machine metal materials. And through-mask electrochemical machining is a very important technology in the processing array structure of difficult-to-cut metal materials ...
Hansong Li, Guoqian Wang, Xin Zheng, Yongbin Zeng   +3 more
doaj   +1 more source

Chloride Induced Secondary Passive Film Failure for Laser Additive Manufacturing Nickel-Based Superalloys during Electrochemical Machining

, 2023
We investigated the influence of chloride on the secondary passive film (SPF) on laser directed energy deposition Alloy 718 during electrochemical machining.
Xin Lin, Inger Odnevall, Shaoli Zhang, Pengfei Guo, Zhang, Yufeng,, Lin, Changjian,, Guo, Pengfei,, Zhang, Shaoli,, Yuan Yang, Qiang Wu, Yufeng Zhang, Yang, Yuan,, Lin, Xin,, Odnevall, Inger,, Changjian Lin, Huang, Weidong,, Wu, Qiang,, Macdonald, Digby D.,, Digby D. Macdonald, Weidong Huang   +19 more
core   +1 more source

Pulsed electrochemical machining of powder metallurgy steels

, 2011
S.68-75In this study, the potential of pulsed electrochemical machining (PECM) for the machining of powder metallurgy steels (PM-steels) is presented. PM-steels are characterized by high hardness and high wear resistance, so that they are commonly used ...
Zinecker, Mike, Schubert, Andreas, Edelmann, Jan, Hackert-Oschätzchen, M., Meichsner, Gunnar   +4 more
core   +1 more source