Results 11 to 20 of about 36,763 (279)
Crystals, 2021 In this work, the fabrication of three Al-2wt.% SiC nanocomposites processed by novel milling route was carried out. The beneficial influence of milling route on the corrosion passivation of the new fabricated composites was investigated.
Saud M. Almotairy +5 more
doaj +1 more source
International Journal of Electrochemical Science, 2020 Ti40 titanium alloy is a typical difficult-to-cut material with high tensile strength and toughness. To achieve both high efficiency and high precision, this paper proposes a machining method combining electrochemical milling for rough machining and ...
Xizhong Wang, Hansong Li, Shen Niu
doaj +1 more source
Influence of Milling–Electrochemical Polishing on Corrosion Resistance of NiTi Shape Memory Alloy
Micromachines, 2022 As an important artificial implant material, the corrosion resistance of NiTi shape memory alloy is closely related to the machined surface quality. In this paper, the multiple analysis methods concerning potentiodynamic polarization, impedance spectrum ...
Guijie Wang +5 more
doaj +1 more source
Plane Machining by Inner-Jet Electrochemical Milling of TiB2/7050 Aluminum Matrix Composite
Applied Sciences, 2021 Electrochemical milling (ECM) is an ideal technique for machining thin-walled structural parts of aluminum matrix composites. Adopting a reasonable tool cathode structure, feed rate, and processing method can improve the machining efficiency.
Binsen He +4 more
doaj +1 more source
Journal of Materials Research and Technology, 2020 Nickel-titanium shape memory alloys have been widely used in medical fields due to their unique shape memory effect, superelasticity, corrosion resistance and biocompatibility.
Guijie Wang +4 more
doaj +1 more source
Important criteria for measuring heritage building condition [PDF]
, 2017 The excellence condition of a heritage building lies not only in the appearance of its individual elements, but also in the integrity of all its components, considered as unique criteria of the specific construction technology of its time and place ...
Abdul Rahman, Mohammad Ashraf +2 more
core +1 more source
Polyol mediated synthesis and electrochemical performance of nanostructured LiMn2O4 cathodes
International Journal of Electrochemical Science, 2016 Nanoparticulate single phase LiMn2O4 spinel was prepared via polyol method and applied as a cathode in a lithium ion battery. The effects of calcination temperature (250 °C – 800 °C) as well as of post-synthetic treatment by ball milling on the ...
Shuo Yang +3 more
doaj +1 more source
Electrochemical Noise Response of Cr2Nb Powders Applying Mechanical Alloying
Crystals, 2022 Cr2Nb alloys are potential candidates for high-temperature structural materials. The influence of different mechanical alloying parameters (milling time) and sintering processes were studied. After mechanical alloying and observation by scanning electron
Claudia Georgina Nava-Dino +6 more
doaj +1 more source
Electrochemical oxidation of olive oil mill wastewaters
Water Research, 2005 The electrochemical oxidation of olive oil mill wastewaters over a titanium-tantalum-platinum-iridium anode was investigated. Batch experiments were conducted in a flow-through electrolytic cell with internal recycle at voltage of 5, 7 and 9 V, NaCl concentrations of 1%, 2% and 4%, recirculation rates of 0.4 and 0.62 L/s and initial chemical oxygen ...
Elefteria Psillakis() +4 more
openaire +3 more sources
Carbon Trends, 2021 Controlled structural and chemical defects were induced on to graphene oxide (GO) by mechanical milling of the precursor graphitic sheets for different times followed by their chemical oxidation. Raman, XRD, FTIR, XPS and AFM measurements was carried out
R. Ashwini +4 more
doaj +1 more source