Results 61 to 70 of about 7,216 (255)

Study of Formed Oxides in IN718 Alloy during the Fabrication by Selective Laser Melting and Electron Beam Melting

Metals, 2018
This study confirmed that Al2O3 particles were formed in IN718 alloys during the fabrication by both selective laser melting (SLM) and electron beam melting (EBM). Different heat pattern and atmospheres in SLM and EBM result in different distribution and
Hao Yu, Shigenari Hayashi, Koji Kakehi, Yen-Ling Kuo   +3 more
doaj   +1 more source

Porosity of Additive Manufacturing Products Obtained by Selective Electron Beam Melting

Elektronnaya Obrabotka Materialov
The paper presents some investigation results of the material porosity of the samples made using the techno-logy of selective electron beam melting from the Ti-6Al-4V alloy powder. The influence of hatching mode parameters on the porosity of samples was carried out using optical microscopy and X-ray computed tomography.
E. V. Krasnova, Yu. A. Morgunov, B. P. Saushkin, N. V. Khomyakova   +3 more
openaire   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

External and Internal Cracking Caused by Heat Treatment in Laser Powder Bed Fusion‐Fabricated Inconel 738LC Components

Advanced Engineering Materials, EarlyView.
Manufacturing problems such as heat treatment‐induced cracking hinder the widespread application of the laser powder bed fusion (LPBF) process to superalloys. In this study, cracks in the LPBF components of Inconel 738LC superalloy are characterized after heat treatment at various temperature ranges, revealing two distinct cracking behaviors.
Kosuke Kuwabara, Masahiro Kusano, Ayako Ikeda, Toshio Osada, Makoto Watanabe   +4 more
wiley   +1 more source

Extrusion‐Based Additive Manufacturing of Advanced Ceramics: Strengthening Mechanisms and Process Optimization Review

Advanced Engineering Materials, EarlyView.
This review comprehensively evaluates extrusion‐based additive manufacturing for advanced ceramics, detailing feedstock options and key process parameters. By critically addressing defect mechanisms like porosity and cracking, the work highlights optimization strategies through machine learning and advanced postprocessing.
Meisam Bakhtiari, Mohammad Hadi Sheikh‐Ansari, Avinash Borgaonkar, Mehran Dadkhah, Abdollah Saboori   +4 more
wiley   +1 more source

Formation of topologically closed packed phases within CMSX-4 single crystals produced by additive manufacturing

Materials Letters: X, 2019
The homogeneity of single crystals produced by additive manufacturing (AM) is much higher than that of single crystals produced by the standard investment casting process.
J. Pistor, C. Körner
doaj   +1 more source

Impact of MgO Additions on the Oxidation Resistance and Compression Behavior of Vanadium Alloys

Advanced Engineering Materials, EarlyView.
An increase in oxidation resistance at 600 °C is achieved for alloys containing more than 2.5 wt.% MgO. It has been established that, along with V2O5, MgO6V2, and Mg2O7V2 are formed, which are presumed to enhance oxidative stability. Furthermore, the possible transformation of Mg‐vanadates through reaction with CO2, which presumably occurs in this ...
Ievgen Solodkyi, Mathias Galetz, Georg Hasemann, Fabian Lanoy, Emma White, Manja Krüger   +5 more
wiley   +1 more source

Research Progress on Surface Polishing Technology of Powder Bed Fusion Titanium Alloy [PDF]

Cailiao Baohu
Powder bed fusion titanium alloys， as an important metallic material， are widely used in aerospace， medical devices and automotive industries.However， due to their unique material properties and processing methods， surface quality and performance ...
ZHOU Di, WU Songquan, LI Ziyang, LIU Lei, YANG Yi, WANG Hao, HUANG Aijun
doaj   +1 more source

Foundational Machine‐Learning Interatomic Potential for Simulating Chemically Complex Ni‐Based Superalloys

Advanced Engineering Materials, EarlyView.
We apply a foundational machine‐learning interatomic potential based on the graph atomic cluster expansion (GRACE) to simulate the commercial Ni‐based single‐crystal superalloy CMSX‐4. Hybrid Monte‐Carlo/molecular dynamics sampling resolves short‐range order in the γ phase and L12 sublattice occupancies in the γ’ phase and connects them to stacking ...
Aditya Vishwakarma, Sarath Menon, Fritz Körmann, Thomas Hammerschmidt, Ralf Drautz   +4 more
wiley   +1 more source

Microstructure Modification of Additively Manufactured Mo–9Si–8B by Annealing and Its Effects on High‐Temperature Mechanical Properties

Advanced Engineering Materials, EarlyView.
Postbuild annealing systematically modifies the phase fractions and morphology of EB‐PBF processed Mo–9Si–8B. Quantitative microstructure–property correlations reveal how controlled phase evolution enhances high‐temperature compressive strength and creep resistance.
Christopher Schmidt, Yong Chen, Georg Hasemann, Benjamin Wahlmann, Carolin Körner, Manja Krüger   +5 more
wiley   +1 more source