Results 111 to 120 of about 912,001 (286)

The Effect of Composite Flour Composition (Sorghum, Mocaf, and Wheat) on the Elongation, Tensile Strength, and Acceptance of Noodles

open access: yesEngineering Proceedings
This research was conducted to determine the effect of composite flour composition on the elongation, tensile strength, and acceptability of wet noodles. Experimental research was conducted with three different ratios of sorghum flour:mocaf:wheat, namely,
Dina Alviani Prihayati, Eni Purwani
doaj   +1 more source

Características morfogênicas e perfolhamento do Panicum maximum Jacq. cv. Tanzânia irrigado Morphogenetic characteristics and tillering of irrigated Panicum maximum Jacq. cv. Tanzania

open access: yesCiência e Agrotecnologia, 2007
Avaliou-se o efeito de diferentes turnos de rega e níveis de irrigação sobre as características morfogênicas e o perfilhamento de Panicum maximum Jacq. cv. Tanzânia.
Fernando França da Cunha   +4 more
doaj   +1 more source

Manufacturing Continuous Fiber‐Reinforced Printing Filaments: Development of a Post‐Consolidation Unit

open access: yesAdvanced Engineering Materials, EarlyView.
A novel, temperature‐controlled post‐consolidation unit is developed to test its potential to improve the melt impregnation process used to manufacture continuous fiber‐reinforced filaments for additive manufacturing of high‐performance thermoplastics.
Daniel Beermann   +2 more
wiley   +1 more source

Unidirectional Tape‐Based Composites from Hemp and Pineapple Leaf Fiber: Mechanical Performance in Conventional and Bio‐Based Matrices

open access: yesAdvanced Engineering Materials, EarlyView.
The study investigates novel semi‐finished products made of unidirectionally arranged hemp or pineapple leaf fiber‐reinforced composites produced from different matrices. The materials are analyzed in terms of their mechanical and interfacial properties and void content.
Nina Graupner   +22 more
wiley   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

open access: yesAdvanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti   +11 more
wiley   +1 more source

The Effect of Arterial Elongation on Isolated Common Iliac Artery Pathologies

open access: yesLife
Purpose: to investigate the effects of vessel geometry on steno-occlusive and dilatative common iliac artery (CIA) pathologies. Methods: this single-center, retrospective study included 100 participants, namely 60 participants with a unilateral, isolated
Ádám Szőnyi   +7 more
doaj   +1 more source

Microstructural Evolution and Vacancy Defect Formation in Mn–Mo–Ni RPV Steel Under Low Cycle Fatigue: Insights From EBSD and PALS

open access: yesAdvanced Engineering Materials, EarlyView.
Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar   +2 more
wiley   +1 more source

Experience in the treatment of long-gap esophageal atresia by intraluminal esophageal stretching elongation

open access: yesFrontiers in Pediatrics
ObjectiveTo summarize the experience with intraluminal esophageal stretching elongation (ILESE) in the successful treatment of long-gap esophageal atresia (LGEA) at a single center.MethodsClinical data of 68 neonates who underwent LGEA between February ...
Ning Zhang   +6 more
doaj   +1 more source

Structure-Sensitive Mechanism of Nanographene Failure

open access: yes, 2010
The response of a nanographene sheet to external stresses is considered in terms of a mechanochemical reaction. The quantum chemical realization of the approach is based on a coordinate-of-reaction concept for the purpose of introducing a mechanochemical
A. Chuvilin   +31 more
core   +1 more source

Tribological Performance of 60NiTi Alloy Under Varying Contact Conditions and Elevated Temperatures in Linear Reciprocating Sliding

open access: yesAdvanced Engineering Materials, EarlyView.
This study investigates the tribological response of 60NiTi alloy under dry, water‐lubricated and high‐temperature conditions. The alloy exhibits decreasing wear volume and friction with increasing temperature due to the formation of protective oxide layers. The work clarifies dominant wear mechanisms and demonstrates the suitability of 60NiTi for high‐
Anthony Onyebuchi Okoani   +2 more
wiley   +1 more source

Home - About - Disclaimer - Privacy