Results 261 to 270 of about 62,254 (283)

Attaching plates to end mills

Russian Engineering Research, 2009
Test results for end roughing mills with two types of attachment of the rhombic hard-alloy plates are outlined. The replaceable multifaceted plates are attached by inserting a pin or a screw through the central hole. Comparison of the mills’ performance is based on rotation of the plates relative to the supporting surfaces and also on the magnitude of ...
V. A. Pukhal’skii, V. A. Panaioti, P. V. Pukhal’skii   +2 more
openaire   +1 more source

Solid Ceramic Toroidal End Mill

Russian Engineering Research, 2019
The possibility of designing solid ceramic end mills with different geometry is considered. A mathematical model is developed for the cutting section of the mill on the basis of functional relations between the main geometric parameters of a ceramic end mill with a toroidal cutting section.
V. A. Grechishnikov, S. N. Grigoriev, P. M. Pivkin, A. V. Isaev, M. A. Volosova, P. Yu. Peretyagin   +5 more
openaire   +1 more source

Attractive manifolds in end milling

Russian Engineering Research, 2017
The attractive manifolds formed in end milling are analyzed. Such states are formed if the trajectories of steady periodic deformational tool displacements are unstable overall or in individual sections. In the dynamic milling system, attractive manifolds in the form of limit cycles, invariant tori, and strange (chaotic) attractors may appear ...
V. L. Zakovorotny, A. A. Gubanova, A. D. Lukyanov   +2 more
openaire   +1 more source

Gainsford End Mill, Toppesfield, Essex

2007
HER ...
openaire   +1 more source

Programmable end milling of thermoplastics

Russian Engineering Research, 2017
The end milling of industrial and engineering thermoplastics on numerically controlled machine tools is considered. Specifically, attention focuses on the sources and prevention of machining defects. Recommendations are made regarding the selection of the tool geometry, the cutting conditions, and the mill trajectory.
A. A. Emel’yanenko, O. I. Zhabin, Yu. N. Polyanchikov   +2 more
openaire   +1 more source

Fuzzy supervisory control of end milling process

Information Sciences, 1996
Abstract The necessity of raising the efficiency of the milling process in a vertical (end) milling machine determines the implementation of a supervisory control system, which should manipulate the cutting process variables, in order to keep constant a high level of the cutting force.
Haber, Rodolfo, Alique, José R., Ros, Salvador, Peres, Clodeinir R.   +3 more
openaire   +1 more source

Numbering Systems for End Mills

2017
<div class="section abstract"> <div class="htmlview paragraph">This SAE Recommended Practice provides a systematic method for the identification of End Mills. It is intended to assist in the cataloging and supplying of these tools.</div> <div class="htmlview paragraph">NOTE 1— Caution must be taken when assigning codes for ...
openaire   +1 more source

Numbering Systems for End Mills

2019
<div class="section abstract"> <div class="htmlview paragraph">This SAE Recommended Practice provides a systematic method for the identification of End Mills. It is intended to assist in the cataloging and supplying of these tools.</div> <div class="htmlview paragraph">NOTE 1— Caution must be taken when assigning codes for ...
openaire   +1 more source

3352 End Milling of Titanium Alloy with a Textured Ball End Mill

Proceedings of International Conference on Leading Edge Manufacturing in 21st century : LEM21, 2011
Toshiyuki OBIKAWA, Bunji KANI
openaire   +1 more source

Ultra small Micro End Mills

2014
Jan Aurich, Ingo Reichenbach, Martin Bohley   +2 more
openaire   +1 more source