Results 71 to 80 of about 5,838,124 (351)

Low‐Angle Grain Boundaries and Re‐Segregation in Single‐Crystalline Ni‐Base Superalloys

Advanced Engineering Materials, EarlyView.
This work demonstrates that Re‐segregation at low‐angle grain boundaries (LAGBs) in Ni‐base superalloys is influenced by misorientation angle. Advanced microscopy and atom probe tomography reveal that higher misorientation angles increases Re‐segregation.
Alireza B. Parsa, Aparna Saksena, Alesander Kostka, Pascal Thome, Felicitas Scholz, Alexandre Mussi, Christoph Somsen, Baptiste Gault, Jan Frenzel, Gunther Eggeler   +9 more
wiley   +1 more source

Tool wear propagation in Ti6Al4V laser assisted micro milling using micro ball end mill [PDF]

Jurnal Tribologi, 2018
This paper presents an experimental study of laser assisted micro milling of Ti6Al4V using micro ball end mill. Tool wear propagation was observed and compared between conventional and laser assisted micro milling to evaluate the effectiveness of laser ...
Zazuli Mohid, E. A. Rahim
doaj  

Raman Spectroscopic Identification of Oxide Phases in a Corroded MgO–Steel Composite Anode Used in Aluminum Molten Salt Electrolysis

Advanced Engineering Materials, EarlyView.
Micro‐Raman spectroscopy is applied to characterize corrosion products in a recycled‐based MgO–316L steel composite anode after molten salt electrolysis. A depth‐dependent Fe–O/Fe–Al–O layer sequence of magnetite, hercynite, and an Al‐doped magnetite transition zone is identified.
Felix Drechsler, Serhii Yaroshevskyi, Alexander Adamczyk, Mahnaz Mehdizadehlima, Julia Richter, Cameliu Himcinschi, David Rafaja, Alexandros Charitos, Christos G. Aneziris, Jens Kortus   +9 more
wiley   +1 more source

Modelling High Speed Machining with the SPH Method [PDF]

, 2008
The purpose of this work is to evaluate the use of the Smoothed Particle Hydrodynamics (SPH) method within the framework of high speed cutting modelling. First, a 2D SPH based model is carried out using the LS-DYNA® software.
Chieragatti, Rémy, Espinosa, Christine, Lacome, Jean-Luc, Limido, Jérôme, Mabru, Catherine, Salaün, Michel   +5 more
core  

Microstructure Design of Steel‐Spinel Composites via Spark Plasma Sintering Process

Advanced Engineering Materials, EarlyView.
This study illustrates how spark plasma sintering at reduced oxygen partial pressure enables controlled formation of steel‐spinel composites through tailored redox reactions and cation exchange. Comparison of the MgO–Fe2O3, steel–(MgO+Cr2O3), and steel–(MgO+Fe2O3) systems shows how oxygen activity and interface chemistry govern spinel formation, phase ...
Mahnaz Mehdizadehlima, Christian Schimpf, Stefan Martin, Olga Fabrichnaya, David Rafaja   +4 more
wiley   +1 more source

Milling Characteristics and Damage Assessment of Ultrasonic Vibration-Assisted End Milling Cf/SiC Composites

Chinese Journal of Mechanical Engineering
Cf/SiC composites are characterized as anisotropic, heterogeneous, brittle, and hard materials. The process of manufacturing Cf/SiC composites using traditional machining techniques is prone to edge chipping damage and tool wear, which makes it difficult
Zhongwang Wang, Zhigang Dong, Yan Bao, Yichuan Ran, Renke Kang   +4 more
doaj   +1 more source

Tailoring Functional Properties of Ti–Ni–Cu Shape Memory Alloy Thin Films for MEMS Actuators

Advanced Engineering Materials, EarlyView.
A comprehensive study of critical parameters required to develop well‐performing Ti–Ni–Cu thin film shape memory alloy microactuators is provided. Materials science and device integration aspects are integrated by addressing structural and physical relationships using complementary characterization techniques as well as a practical fabrication solution
Elaheh Akbarnejad, Aleksander Kostka, Gowtham Arivanandhan, Yujiao Li, Alan Savan, Manfred Kohl, Alfred Ludwig   +6 more
wiley   +1 more source

A Hybrid Chatter Detection Method Based on WPD, SSA, and SVM-PSO

Shock and Vibration, 2020
As a kind of self-excited vibrations, chatter vibration is extremely common in end milling, especially in high-speed cutting processes. It affects the machining accuracy of products and decreases the processing efficiency of machine tools.
Erhua Wang, Peng Yan, Jie Liu
doaj   +1 more source

The effect of an organic pentasulfide EP additive in turning and milling operations [PDF]

, 2014
Coopération avec Ecole Centrale LyonBecause a cutting fluid could be equally used for different cutting operations, this study proposed to investigate the behavior of a well-known extreme-pressure additive (pentasulfide) in both turning and milling ...
BIERLA, Aleksandra, FROMENTIN, Guillaume, LE MOGNE, Thierry, MARTIN, Jean-Michel, MINFRAY, Clotilde   +4 more
core   +4 more sources

Understanding and Optimizing Li Substitution in P2‐Type Sodium Layered Oxides for Sodium‐Ion Batteries

Advanced Functional Materials, EarlyView.
This work explores Li‐substituted P2 layered oxides for Na‐ion batteries by crystallographic and electrochemical studies. The effect of lithium on superstructure orderings, on phase transitions during synthesis and electrochemical cycling and on the interplay of O‐ versus TM‐redox is revealed via various advanced techniques, including semi‐simultaneous 
Mingfeng Xu, Giovanni Gammaitoni, Michael Häfner, Eduardo Villalobos‐Portillo, Carlo Marini, Matteo Bianchini   +5 more
wiley   +1 more source