Results 161 to 170 of about 7,104 (217)
Antibiofilm and antimetabolic effects of disinfectants on Pseudomonas aeruginosa strains isolated from cosmetic manufacturing environments. [PDF]
Appl Microbiol BiotechnolKorzekwa K +6 more
europepmc +1 more source
Vulcanization Characteristics and Static/Dynamic Mechanical Properties of Chlorinated Butyl Rubber Matrix Materials. [PDF]
Polymers (Basel)Wang K, Lv H, Liu Z.
europepmc +1 more source
Investigation of microbiological non-compliance of endoscopic final rinse water associated with opportunistic premise plumbing pathogens contamination in connecting tube. [PDF]
Sci RepLiu M +7 more
europepmc +1 more source
Experimental Study on the Blending of EPDM/R-EPDM
Advanced Materials Research, 2011 The mechanical properties of EPDM/R-EPDM blending was investigated. Effect of the blending ratio, amount of DCP and silica and the curing temperature of EPDM/R-EPDM blend was discussed respectively. The results showed that each factor of the formulation has an optimum value or range.
Chuan Sheng Wang +2 more
openaire +2 more sources
Utilization of Powdered EPDM Scrap in EPDM Compound
Rubber Chemistry and Technology, 2003 Abstract Processability, curing characteristics and vulcanizate properties of EPDM compounds containing ground waste EPDM (W-EPDM) have been studied. Ground waste was prepared from factory scraps, using a mechanical grinder with silicon carbide abrasive wheel rotating at 2950 rpm.
Ceni Jacob +3 more
openaire +2 more sources
Journal of Elastomers & Plastics, 2002 The graft polymerization of acrylonitrile (AN) or acrylic acid (AA) onto ethylene-propylene-diene terpolymer rubber (EPDM) was carried out in toluene, using dibenzoyl peroxide (BPO) as an initiator. The synthesized AN-g-EPDM and AA-g-EPDM were characterized by FT-IR spectroscopy and thermal gravimetric analysis (TGA).
S. H. Botros, A. F. Moustafa
openaire +2 more sources
EPDM/CIIR Blends: Effect of EPDM Grade on Mechanical Properties
International Journal of Polymeric Materials, 2007 Blends of chlorobutyl rubber (CIIR) with two grades of ethylene-propylene diene monomer rubber (EPDM) were prepared and the effect of blend ratio on the cure characteristics, hot air ageing resistance, steam ageing resistance, and mechanical properties were evaluated.
Sunil Jose T., Joseph Rani
openaire +2 more sources
Co-Curing of EPDM and Diene Rubbers by Grafting Accelerators Onto EPDM
Rubber Chemistry and Technology, 1974 Abstract The object of this work was to find ways to co-cure blends of EPDM and diene rubbers for improved properties. We found that by grafting accelerators onto EPDM we obtain excellent cure compatibility between EPDM and natural rubber.
K. C. Baranwal, P. N. Son
openaire +2 more sources
Journal of Applied Polymer Science, 1987 AbstractThe effect of oxidative and thermal aging of EPDM raw rubber and rubber vulcanizate on gelation, network structure, and techical properties has been studied over a wide range of temperatures and times of aging. Three grades of EPDM having different types of diene have been considered.
A. Saha Deuri, Anil K. Bhowmick
openaire +2 more sources
Some of the next articles are maybe not open access.
Related searches:
Related searches:
International Polymer Science and Technology, 2004
EPDM polymers have been used in automotive weather seals for more than 30 years and there have been numerous investigations into their mixing and extrusion. However, the stability of EPDM polymers under the heat and shear forces that occur during the production of composites is generally ignored and inadequately understood.
HJ Graf, ST Yu, L Di Agnillo
openaire +1 more source
EPDM polymers have been used in automotive weather seals for more than 30 years and there have been numerous investigations into their mixing and extrusion. However, the stability of EPDM polymers under the heat and shear forces that occur during the production of composites is generally ignored and inadequately understood.
HJ Graf, ST Yu, L Di Agnillo
openaire +1 more source