Results 281 to 290 of about 695,264 (389)

Development and characterisation of antimicrobial epoxy resin. [PDF]

Sci Rep
Berrow M, Brooks A, Kotowska AM, Watts J, Riordan L, Kidger L, Scurr DJ, Nikoi ND, Banzhaf M, Bryant JA, Greenway S, Mendez V, Norton B, de Cogan F.   +13 more
europepmc   +1 more source

Dielectric Barrier Discharge Electrothermal Heating and Additive Manufacturing of Thermoset Parts

Advanced Materials Technologies, EarlyView.
3D printing of thermosets is difficult due to the low yield stress of most uncured resins. However, by locally heating resin using a non‐equilibrium plasma, layers can be partially cured and printing enabled. Plasma application to a liquid epoxy/carbon nanotube composite is observed to cause rapid surface heating and oxidation of the cured layers ...
Ethan M. Harkin, Sayyam Deshpande, Smita Shivraj Dasari, Micah J. Green   +3 more
wiley   +1 more source

Numerical Modeling of Micro-Mechanical Residual Stresses in Carbon-Epoxy Composites During the Curing Process. [PDF]

Polymers (Basel)
Verde R, D'Amore A, Grassia L.
europepmc   +1 more source

Transformative 4D Printed SMPs into Soft Electronics and Adaptive Structures: Innovations and Practical Insights

Advanced Materials Technologies, EarlyView.
This review highlights recent advancements in 3DP techniques that incorporate emerging multifunctional SMP materials for applications in e‐electronics, soft actuators, biomedical devices, and more. Abstract Shape memory polymers (SMP) have recently gained significant attention as multifunctional materials for flexible and wearable electronics ...
Muhammad Yasir Khalid, Adam Otabil, Omar Samir Mamoun, Khalid Askar, Mahdi Bodaghi   +4 more
wiley   +1 more source

Experimental Investigations on Microstructure, Properties and Wear Behavior of Chopped Basalt Fiber and Molybdenum Disulfide Reinforced Epoxy Matrix Composites. [PDF]

Polymers (Basel)
P C SK, Ravichandran M, Mohanavel V, Radhika N.   +3 more
europepmc   +1 more source

From the Discovery of the Giant Magnetocaloric Effect to the Development of High‐Power‐Density Systems

Advanced Materials Technologies, EarlyView.
The article overviews past and current efforts on caloric materials and systems, highlighting the contributions of Ames National Laboratory to the field. Solid‐state caloric heat pumping is an innovative method that can be implemented in a wide range of cooling and heating applications.
Agata Czernuszewicz, Yaroslav Mudryk, Jun Cui, Lucas Griffith, Duane D. Johnson, Julie Slaughter   +5 more
wiley   +1 more source

FRACTURE BEHAVIOR OF EPOXY/CLAY AND EPOXY/SILICA NANOCOMPOSITES

, 2003
Hiroaki Miyagawa, Lawrence T. Drzal
openaire   +1 more source

Improved Mechanical and Physical Properties of Epoxy Acrylate Oligomers by Chemical Modification for the Effective Encapsulation of the Triple-Cation Perovskite Solar Cells. [PDF]

ACS Omega
Ercan BT, Mutlu A, Gultekin SS, Gultekin B, Dincalp H, Zafer C.   +5 more
europepmc   +1 more source

Transforming Plastic Waste into Strain Sensors: Multifunctional Upcycled TPEE Elastomers with MXene Multilayer Assemblies

Advanced Materials Technologies, EarlyView.
A sustainable approach is reported for upcycling PET waste into thermoplastic polyester elastomer (TPEE)‐based films with advanced properties, specifically designed for applications in strain sensing, conductivity, and photothermal response. Through a layer‐by‐layer deposition technique, TPEE films are fabricated with bio‐compatible chitosan (CH) or ...
Chun‐Ting Chang, Chia‐Wei Chang, Jian‐Hua Ciou, Kai‐Chuan Kuo, Ji Lin, Chia‐Ti Wu, Mei‐Li Li, Yu‐Hsuan Tseng, Yu‐Liang Lin, Che‐Tseng Lin, Jiun‐Tai Chen   +10 more
wiley   +1 more source

The Effect of Nano-Biochar Derived from Olive Waste on the Thermal and Mechanical Properties of Epoxy Composites. [PDF]

Polymers (Basel)
Özgün Mİ, Erci V, Madenci E, Erci F.
europepmc   +1 more source