Results 201 to 210 of about 173,503,456 (301)

3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement

Advanced Engineering Materials, EarlyView.
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin, Gloria R. Young, Francesca Tallia, Reece N. Oosterbeek, Shaaz Ghouse, Edward Spiers, Nupur Kohli, Tom Briggs, Marc Masen, Siwei Li, Ren‐Jei Chung, Jonathan R. T. Jeffers, Julian R. Jones   +12 more
wiley   +1 more source

An Immersed Interface Method for Incompressible Flows and Near Contact. [PDF]

J Comput Phys
Facci MJ, Sun Q, Griffith BE.
europepmc   +1 more source

The Role of Ultra‐Thin Passive Films and Organic Adsorbates on Aluminum Chips for a Friction‐Induced Solid‐State Recycling Process

Advanced Engineering Materials, EarlyView.
Despite benefits to storage stability and handleability of aluminum scrap, octadecyl phosphonic acid (ODPA) SAMs reduce the tensile strength of wires produced using friction‐induced recycling. Etching and methyl diphosphonic acid (MDPA) coatings, however, have little effect.
Timothy D. Goller, Steffen Gabsa, Werner Homberg, Guido Grundmeier   +3 more
wiley   +1 more source

Analytical Investigation of Non-Local Optoelectronic Photo-Thermoelastic Response in Fiber-Reinforced Anisotropic Silicon Using an Eigenvalue Framework. [PDF]

Nanomaterials (Basel)
Emam A, Yusuf M, El-Dali A, Mrzog Alaofi Z.   +3 more
europepmc   +1 more source

Elastic–Plastic Modeling and Experimental Characterization of Granular Jamming Actuators

Advanced Engineering Materials, EarlyView.
Granular jamming enables rapid switching between soft and rigid mechanical states. Here, a reduced‐order elastic‐perfectly‐plastic beam framework captures pressure‐dependent loading, unloading, residual deformation, and hysteresis in jammed beams, while matching three‐point bending experiments across materials and geometries. The framework links design
Saheli Patel, Prashant K. Purohit, Jordan R. Raney   +2 more
wiley   +1 more source

Intelligent neural network-based framework for Maxwell nanofluid flow with Soret-Dufour coupling and nonlinear thermal radiation. [PDF]

Discov Nano
Ishaq M, Ashraf MB, Fantaye AK, Zayani HM, Alshehery S, Alsawah GA, Khedher NB.   +6 more
europepmc   +1 more source

Rotary 3D Printing With Integrated Electroplating

Advanced Engineering Materials, EarlyView.
A rotary material extrusion platform integrates localized copper electroplating with printing and encapsulation to fabricate cylindrical polymer–metal structures containing fully embedded, low‐resistance conductive pathways that enable internal Joule heating and thermally activated shape‐memory responses.
Antonio Zagaria, Nicola Larovere, Moslem Mohammadi, Gianluca Percoco, Ali Zolfagharian, Gianni Stano   +5 more
wiley   +1 more source

Evolution of Hypoequilibrium States in Steepest Entropy Ascent Models for Nonequilibrium Quantum Thermodynamics. [PDF]

Entropy (Basel)
Beretta GP, Ray RK, von Spakovsky MR.
europepmc   +1 more source

Impact of the Process Atmosphere During Hot Isostatic Pressing on the Near‐Surface Composition of an Additively Manufactured Austenitic High‐Interstitial Steel

Advanced Engineering Materials, EarlyView.
A high interstital austenitic steel is additively manufactured and postdensified by HIP to eliminate gas porosity. Thereby, the loss of N and Mn in Ar HIP atmosphere is investigated. Further, HIP using N2 atmosphere is investigated which led to excessive nitride formation.
F. Großwendt, J. Hahn, J. Kimm, S. Weber, J. Lentz   +4 more
wiley   +1 more source

Dynamics near equilibria in the Jupiter-Europa system using the Lie-series technique. [PDF]

Sci Rep
Tarek D, Sirwah MA, Radwan M, Dwidar HR.
europepmc   +1 more source