Results 101 to 110 of about 237,518 (267)

Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants

Advanced Engineering Materials, EarlyView.
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir, Jixing Lin, Yuncang Li, Li Zhu, Paul F. A. Wright, Cuie Wen   +5 more
wiley   +1 more source

Data-driven multivariate time series prediction of in-vehicle equipment failure rates

Journal of Engineering and Applied Science
Effectively predicting the failure rate of train-controlled on-board equipment is of great significance for rationally allocating equipment spares, drawing up maintenance plans, and reducing the occurrence of failures.
Yongfei Guo, Yonggang Chen, Haiyong Wang, Yang Liu   +3 more
doaj   +1 more source

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

Advanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar, Akash Vyas, Mohammad Aatif Qazi, Nashit Jalal, Maria Ophelia Jarligo, Mostafa Yakout, Jing Liu, André McDonald   +7 more
wiley   +1 more source

Equipment failure of intravenous syringe pump detected by increase in Narcotrend stage: A case report. [PDF]

Medicine (Baltimore), 2018
Niu K, Guo C, Han C, Teng S.
europepmc   +1 more source

Influence of Surface Finish on the Tribological Performance of AlTiBN Coatings Deposited on Forming Tools

Advanced Engineering Materials, EarlyView.
Aluminum and nitride coatings are used in industry because they are hard, resist wear, and protect against oxidation. Adding boron can improve friction behavior and other properties. This study tests coatings on surfaces with different finishes. Results show smoother surfaces perform better, while rough ones wear faster, although coatings can reduce ...
Adrián Claver, Iker Alfonso, Eneko Barba, Javier León, José Antonio García, Iñaki Zalakain, Iván Fernández Martínez, Arley García‐Carrero, Christian Almeyda, Daniel Salcedo   +9 more
wiley   +1 more source

Experimental Characterization and Constitutive Modeling of the Effect of Prior Inelastic Strain on the Viscoplastic Behavior of AD730 at 700 °C

Advanced Engineering Materials, EarlyView.
This study shows that superalloys used in aircraft engine disks become much more prone to deformation at high temperatures if they have been strained during manufacturing. This effect increases with the level of prior strain but eventually reaches a limit.
Fabio Machado Alves da Fonseca, Patrick Villechaise, Malik Durand, Arnaud Longuet, Florent Coudon, Loïc Signor, Julien De Jaeger, Dominique Eyidi, Nathalie Bozzolo, Jonathan Cormier   +9 more
wiley   +1 more source

Exploration of Pseudobinary Alloys (Al–Mn)‐(Co–Fe–Ni) to Design High‐Entropy and Compositionally Complex Alloys to Stabilize the τ Phase in Al–Mn‐Based Ferromagnetic Alloys

Advanced Engineering Materials, EarlyView.
This experimental study investigates the thermodynamic limits of the Al–Mn τ ferromagnetic phase within complex‐composition alloys (CCAs). Using nine rare‐earth‐free compositions, it explores a broad region of the pseudobinary AlMnCoFeNi system. The results reveal intricate links between composition, phase stability, and magnetic behavior, highlighting
Sacha Plagnol‐Chauzu, Laurent Peltier, Fodil Meraghni, Stéphane Delalande, Frédéric Mazaleyrat   +4 more
wiley   +1 more source

From Shear to Sound: Mechanics–Acoustics Mapping of TPMS Lattices

Advanced Engineering Materials, EarlyView.
Triply periodic minimal surface (TPMS) lattices are mapped across mechanical and acoustic performance, revealing that descriptors validated in compression fail under shear. First‐time comparison with trusses included. A transition from porous to resonance‐driven absorption emerges at 25% density.
Lucía Doyle, María Ángeles Navacerrada, Johan Christensen, Carlos González   +3 more
wiley   +1 more source

Designing Polymer Nanocomposites for X‐Ray Shielding: Mechanisms, Architectures, and Scalable Processing

Advanced Engineering Materials, EarlyView.
This review highlights advances in lightweight, lead‐free polymer nanocomposites for diagnostic X‐ray shielding. By linking filler chemistry, dispersion, architecture, and photon interaction mechanisms, it establishes structure–performance relationships guiding material design.
Aklilu G. Messele, Hossein Ipakchi, Tizazu H. Mekonnen   +2 more
wiley   +1 more source

Influence of Geometric Design on Mechanical Performance of Auxetic Metastructure

Advanced Engineering Materials, EarlyView.
Strategic geometric reinforcement transforms auxetic performance. This study evaluates 3D‐printed arrowhead metastructures, revealing that a modified design with local ring reinforcement suppresses premature failure to achieve superior energy absorption and structural efficiency.
Muhammad Gulzari, Supharoek Sornsomrit, Muhammad Ayaz Akbar, Stephan Rudykh   +3 more
wiley   +1 more source