Results 71 to 80 of about 1,078,015 (165)

Characterization of nonlinear switching in a figure-of-eight fiber laser using frequency-resolved optical gating [PDF]

open access: yes, 1998
The measurement technique of frequency-resolved optical gating is applied to determine the nonlinear switching characteristics of a passively modelocked figure-of-eight erbium-doped fiber laser. By completely characterizing the intensity and phase of the
Barry, Liam P.   +4 more
core   +2 more sources

Enhanced Thermal Stability in Compact ASE Sources Enabled by Optimized Erbium-Doped Fiber Design

open access: yesPhotonics
Amplified Spontaneous Emission (ASE) sources are widely employed as highly stable broadband sources in fields such as high-precision navigation and optical detection.
Jianming Liu   +6 more
doaj   +1 more source

Ultrafast optical properties and applications of anisotropic 2D materials

open access: yesNanophotonics, Volume 13, Issue 2, Page 107-154, January 2024.
Abstract Two‐dimensional (2D) layered materials exhibit strong light‐matter interactions, remarkable excitonic effects, and ultrafast optical response, making them promising for high‐speed on‐chip nanophotonics. Recently, significant attention has been directed towards anisotropic 2D materials (A2DMs) with low in‐plane crystal symmetry. These materials
Sang Ho Suk   +4 more
wiley   +1 more source

Feedback-Injected Erbium Fiber Laser With Selectable Tunability and Constant Single-Longitudinal-Mode Characteristic

open access: yesIEEE Access, 2020
In this investigation, a wavelength-selected single-longitudinal-mode (SLM) erbium-doped fiber (EDF) ring laser utilizing C-band EDF based gain medium over a tuning bandwidth of 1524.0 to 1573.0 nm is demonstrated experimentally.
Chien-Hung Yeh   +4 more
doaj   +1 more source

High power (60mW) single frequency erbium:ytterbium codoped fiber laser

open access: yes, 1997
The characteristics of a high power Er3+:Yb3+ single frequency fiber laser pumped at 980nm are reported. The device gives 60mW output power with RIN 10MHz and linewidth 500kHz.
Dong, L.   +3 more
core   +1 more source

A Selectable Single-Mode Erbium Laser With Power-Flattened Output Employing Dual-Sagnac-Ring

open access: yesIEEE Access, 2019
To achieve wavelength-selectable and stable erbium-doped fiber (EDF) laser, a dual-Sagnac-ring configuration is designed to reach single-longitudinal-mode (SLM) oscillation and power-flattened output simultaneously.
Chien Hung Yeh   +5 more
doaj   +1 more source

Observation of Raman Gain in Reduced Length of Bismuth Erbium Doped Fiber [PDF]

open access: yesJournal of Optoelectronical Nanostructures, 2020
Raman amplification of a 49 cm Bismuth oxide (Bi2O3) as a nonlinear gainmedium based erbium doped fiber amplifier (EDFA) is reported in new and compactdesign in near infrared spectral regions.
شریفه شاهی   +3 more
doaj  

Broad, Tunable and Stable Single-Frequency Erbium Fiber Compound-Ring Lasers Based on Parallel and Series Structures in L-Band Operation

open access: yesPhotonics
In this demonstration, we present two erbium-doped fiber (EDF) lasers, with series and parallel three sub-ring configurations, respectively, to achieve tunable channel output and stable single longitudinal mode (SLM) operation in the L-band range.
Yu-Ting Lai   +8 more
doaj   +1 more source

Erbium-doped-fiber-based broad visible range frequency comb with a 30 GHz mode spacing for astronomical applications

open access: yes, 2021
Optical frequency combs have the potential to improve the precision of the radial velocity measurement of celestial bodies, leading to breakthroughs in such fields as exoplanet exploration. For these purposes, the comb must have a broad spectral coverage
Keisuke Nakamura (304936)   +3 more
core   +1 more source

Graphene-Oxide-Based Saturable Absorber for All-Fiber Q-Switching With a Simple Optical Deposition Technique

open access: yesIEEE Photonics Journal, 2012
A Q-switched erbium-doped fiber laser (EDFL) incorporating a graphene-oxide-based saturable absorber (SA) is proposed and demonstrated. The SA is fabricated by first dissolving graphene oxide nanopowder in water and subsequently using the thermophoresis ...
H. Ahmad   +3 more
doaj   +1 more source

Home - About - Disclaimer - Privacy