Results 131 to 140 of about 242,082 (256)
An intentionally added, chemically formed LixAlSy coating stabilizes the lithium–electrolyte interface in solid‐state Li–S batteries. The layer suppresses side reactions, preserves smooth charge transfer, and improves ion transport from the start. This approach offers a practical route to more durable solid‐state batteries and a clearer understanding ...
Xinyi Wang +4 more
wiley +1 more source
Polymer binders and thick pressed LLZTO pellets limit all‐solid‐state battery integration through grain‐boundary carbon and high ohmic losses. A binder‐free capillary suspension ink is direct‐ink‐written and sintered into 254 μm$\mu{\rm m}$, 95.8%‐dense Ta‐stabilized LLZTO with 17.3 mS cm−1$\text{cm}^{-1}$ bulk conductivity, enabling thinner ...
Sri Vaishnavi Thummalapalli +7 more
wiley +1 more source
A convenient approach for the synthesis of monodisperse oligo(ethylene glycols) up to 12 units is described. A novel cleavage protocol replacing laborious hydrogenolysis is introduced to achieve a fast, inexpensive and widely applicable procedure.
Lendl, Bernhard +6 more
core +1 more source
Electrospun polycaprolactone fiber mats embedded with diclofenac‐imprinted polymers were developed to remove persistent pharmaceutical pollutants from water. The materials showed improved adsorption and retention compared to pure polymer mats, with performance influenced by fiber diameter and polymer content.
Michael Redel +4 more
wiley +1 more source
This research presents a thermodynamic and acoustic investigation of the monosodium glutamate (MSG) food preservative in an aqueous solution. The addition of polyethylene glycol (PEG 400) and (PEG 600) as a solute is employed to create a ternary solution.
Ansari Ammara Firdaus +2 more
doaj +1 more source
Control of Bacterial Attachment on Macroporous PDMS/Paraffin SLIPS With Varying Lubricant Viscosity
Slippery liquid‐infused porous surfaces (SLIPS) prepared from macroporous PDMS, infused with medical‐grade paraffins, were systematically investigated regarding the correlation of viscosity, surface corrugation, bulk porosity, and bacterial resistance. Substrate porosity was found to dominate lubricant stabilization and the antifouling activity.
Regina Kopecz +3 more
wiley +1 more source
Graphical abstract illustrating the fabrication of Ni–P–O–C porous carbon microlattice electrodes by DLP printing of Ni/P precursor‐containing resin followed by high‐temperature carbonization. The resulting conductive microlattice acts directly as the HER cathode in alkaline electrolyte, where in situ formed Ni–P–O–C interfaces provide active sites for
Muzahir Ali +6 more
wiley +1 more source
Overcoming the immunogenicity challenges of enzyme‐mediated crosslinking, a flow‐through reactor utilizing SFNF‐HRP enables the continuous production of injectable hydrogels. This continuous platform ensures homogeneous crosslinking while minimizing residual HRP in the resulting hydrogels.
Ayari Miyawaki, Shinji Sakai
wiley +1 more source
3D‐Printed Actuator Powered by Liquid Crystal Elastomer Muscles at the Water–Air Interface
Soft robots for unstructured environments require responsive, durable actuators. Liquid crystal elastomers (LCEs) provide large reversible deformations under thermal or optical stimuli. Direct ink writing enables fabrication of LCE actuators integrated with silicone, with mesogen chemistry and oligomers optimized for printable inks.
Cecilie Ryberg +5 more
wiley +1 more source
Red‐Light Tomographic Volumetric 3D Printing in Seconds for Fabrication of Colorless Structures
A custom red‐light‐responsive TVAM platform combines methylene blue, triethanolamine, and PEGDA to fabricate transparent crosslinked hydrogels. Light patterns are projected into a rotating resin container, where a sacrificial photoinitiator system enables rapid polymerization and colorless channel‐containing structures, utilizing low‐energy light for ...
Ali Eftekhari +9 more
wiley +1 more source

