Results 101 to 110 of about 446,657 (296)

Adaptive Foam 3D Printing of Ultralight and Multifunctional Materials

Advanced Engineering Materials, EarlyView.
Adaptive foam 3D printing, enabled by expandable microspheres, imparts cellular structures to thermoplastic and thermosetting polymers, manufactured through a variety of processes including fused filament fabrication, direct ink writing, digital light processing, and inkjet printing.
Nariman Rajabifar, Amir Ameli
wiley   +1 more source

Timescales for the Spray-Mediated Gas Exchange of Carbon Dioxide

Journal of Marine Science and Engineering
The air–sea exchange of carbon dioxide (CO2) on a global scale is a key factor in understanding climate change and predicting its effects. The magnitude of sea spray’s contribution to this flux is currently highly uncertain.
Lucy Hendrickson, Penny Vlahos, Leonel Romero   +2 more
doaj   +1 more source

Self‐Cleaning Sensor Surfaces for Long‐Term Environmental Monitoring

Advanced Engineering Materials, EarlyView.
Long‐term use of unattended outdoor sensors without soiling or biofouling is achieved through generation of a micro‐ and nanorough cuvette surface by combing hydrophobic nanoparticles with fluorinated polymers, crosslinked and surface‐attached through CHic chemistry. The coating demonstrates self‐cleaning behavior and prolonged outdoor stability, which
Sanam Kumari Rajak, Yasmina Frey, Ulrike Wallrabe, Oswald Prucker, Jürgen Rühe   +4 more
wiley   +1 more source

An Ensemble Mean Method for Remote Sensing of Actual Evapotranspiration to Estimate Water Budget Response across a Restoration Landscape

Remote Sensing
Estimates of actual evapotranspiration (ETa) are valuable for effective monitoring and management of water resources. In areas that lack ground-based monitoring networks, remote sensing allows for accurate and consistent estimates of ETa across a broad ...
Roy E. Petrakis, Laura M. Norman, Miguel L. Villarreal, Gabriel B. Senay, MacKenzie O. Friedrichs, Florance Cassassuce, Florent Gomis, Pamela L. Nagler   +7 more
doaj   +1 more source

Fabrication Routes for Ionic Conducting Fiber Strain Sensors

Advanced Engineering Materials, EarlyView.
Ionic conducting fiber strain sensors (ICFSs) offer compliant, textile‐integrable sensing. Thus far, the commercialization of ICFSs has been constrained by fiber fabrication routes. This review provides a fabrication‐centric analysis of ICFSs correlating processing strategies with material properties and scalability.
Leo John Kershaw, Zhanhong Yang, Anne Ladegaard Skov, Magdalena Skowyra   +3 more
wiley   +1 more source

Evaporation in relation to hydrology [PDF]

, 1981
In meteorology some topics enjoy particular interest from other disciplines. The interest of hydrologists for the evaporation of water is a case in point, understandably and rightly so.
Bruijn, H.A.R. de, Stricker, J.N.M., Wartena, L., Bakel, P.J.T. van, Keijman, J.Q., Velds, C.A.   +5 more
core  

Influence of TiC and TiN Ceramic Reinforcements on the Microstructure, Thermal Expansion Behavior, and Tensile Properties of Invar 36 Manufactured by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
This study examines Invar composites reinforced with titanium carbide (TiC) and titanium nitride (TiN) using laser powder bed fusion (LPBF). It presents the influence of reinforcements on microstructure, tensile properties, and thermal expansion. Results show that TiC effectively strengthens Invar while maintaining low thermal expansion, whereas TiN ...
Ayodeji Nathaniel Oyedeji, Natasha Sacks, Johannes Pötschke, Björn Matthey   +3 more
wiley   +1 more source

Feasibility and Limitations of the Advanced Replica Process for Bioactive Glasses

Advanced Engineering Materials, EarlyView.
Periodic 3D‐printed Kelvin‐cell templates enable a controlled advanced replica process for fabricating highly porous glass lattices. Across P45K9, 45S5, and 13–93, material‐dependent differences in coating, burnout, and shrinkage lead to distinct strut morphologies, while comparable final porosities of 83%–88% are retained.
Swantje Funk, Elisabeth Keck, Alberto López‐Grande, Delia S. Brauer, Tobias Fey   +4 more
wiley   +1 more source

Investigating the Low‐Temperature Phase Stability of the Binary Ta–W System

Advanced Engineering Materials, EarlyView.
Atomistic simulations show that the binary Ta–W system forms ordered intermetallic phases, B2‐TaW and D03‐TaW3, as 0 K ground states. Configurational entropy, however, lowers the free energy of the disordered bcc solid solution, which becomes the stable phase above about 400 K.
Klemens Lechner, Anna Sophie Jelinek, Velislava Terziyska, Peter Wagatha, Wolfram Knabl, Christian Mitterer, Helmut Clemens, David Holec   +7 more
wiley   +1 more source

Materials‐Driven Additive Manufacturing for Electrical Machines: Qualification‐Oriented Design Beyond Geometric Freedom

Advanced Engineering Materials, EarlyView.
This perspective reframes additive manufacturing for electrical machines as a qualification‐limited materials and architecture design problem. It links process–structure–property–performance relationships to magnetic, conducting, dielectric, and thermal property windows, highlighting where AM can enable segmented magnetic circuits, permanent magnet ...
Dénes Fodor, Loránd Szabó
wiley   +1 more source