Results 151 to 160 of about 1,013 (197)
Some of the next articles are maybe not open access.
Nanostructure of Vortex During Explosion Welding
Journal of Nanoscience and Nanotechnology, 2011The microstructure of a bimetallic joint made by explosion welding of orthorhombic titanium aluminide (Ti-30Al-16Nb-1Zr-1Mo) with commercially pure titanium is studied. It is found that the welded joint has a multilayered structure including a severely deformed zone observed in both materials, a recrystallized zone of titanium, and a transition zone ...
V V, Rybin +7 more
openaire +2 more sources
Explosive Welding and Cladding
AIP Conference Proceedings, 2004Explosive welding or cladding is usually performed on relative thick plates by means of a large scale parallel plate set‐up. At TNO‐PML several of the explosive welding configurations that were developed mainly in the nineteen sixties and seventies are being investigated for their potential use in modern industrial applications.
openaire +1 more source
Fundamentals of Explosion Welding
1993AbstractExplosion welding (EXW), also known as explosive bonding, is accomplished by a high-velocity oblique impact between two metals. This article describes the practice of producing an explosive bond/weld and draws on many previous research results in order to explain the mechanisms involved.
openaire +1 more source
Wave Forming Mechanisms in Explosive Welding
Materials Science Forum, 2004Experimental results of wavy metal interfaces obtained by explosive welding are presented and used to determine which wave forming mechanism occurred. It was found that for small collision angles (smaller than about 20°) the Von Karman or jet indentation mechanism occurs, while for large collision angles a straight metal interface is obtained. However,
openaire +2 more sources
2003
Number of researches in the field of creating new technologies with impulse tension, have shown that explosion energy can be used in the following processes: processing by deformation (tin-sheet shaping) making holes, volume shaping, clinching, calibrating, surface hardening, sintering, under pressure casting, cleaning the castings, mounting, etc.
Buljan, Stipo +2 more
openaire +2 more sources
Number of researches in the field of creating new technologies with impulse tension, have shown that explosion energy can be used in the following processes: processing by deformation (tin-sheet shaping) making holes, volume shaping, clinching, calibrating, surface hardening, sintering, under pressure casting, cleaning the castings, mounting, etc.
Buljan, Stipo +2 more
openaire +2 more sources
Mechanics of Explosive Welding
1983The explosive welding process is one of the most useful and widely employed applications of the high energy rate methods to the fabrication of materials. Its major advantage lies in that it does not suffer from the limitations imposed on other welding processes by their specific characteristics.
openaire +1 more source
1981
A general review of explosion welding with particular emphasis on metallurgical effects is presented. Explosion welding is basically a solid-phase welding process, in which explosives are used to accelerate the parts to be joined into a high velocity oblique collisions, is fundamental to the welding process.
openaire +1 more source
A general review of explosion welding with particular emphasis on metallurgical effects is presented. Explosion welding is basically a solid-phase welding process, in which explosives are used to accelerate the parts to be joined into a high velocity oblique collisions, is fundamental to the welding process.
openaire +1 more source
Explosive Welding in Planar Geometries
1983Of the various explosively welded components now available, clad plate, with a current world-wide production rate of about 25 000 m2 per annum, is in greatest demand by far. Although the clad plate has extensive direct application in the simplest planar forms in which it is produced, that is to say as rectangles or discs (for tube-plates), other forms ...
M. D. Chadwick, P. W. Jackson
openaire +1 more source
1992
The methods of manufacture of welded composites fall into two main categories, depending on whether the geometry of the system is planar or tubular. A further sub-division occurs with the tubular components which can be produced either in axi- or asymmetric systems.
openaire +1 more source
The methods of manufacture of welded composites fall into two main categories, depending on whether the geometry of the system is planar or tubular. A further sub-division occurs with the tubular components which can be produced either in axi- or asymmetric systems.
openaire +1 more source