Results 251 to 260 of about 26,083 (287)

Studying the Axial Balance of External Gear Pumps

SAE Technical Paper Series, 2005
<div class="htmlview paragraph">In this paper some design aspects related to external gear pumps balancing surfaces are studied, and some useful guidelines for designing bearing blocks balancing surfaces are suggested. In order to study bearing blocks axial balance, a numerical procedure for the determination of the pressure distribution inside ...
BORGHI, Massimo, MILANI, Massimo, PALTRINIERI, Fabrizio, ZARDIN, Barbara   +3 more
openaire   +2 more sources

Geometric displacement optimization of external helical gear pumps

Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 2009
An approach to geometric displacement optimization of external helical gear pumps is presented. In addition, relations of pump flow property and its influence factors are also investigated. During that, only the pumps with transverse contact ratios of not less than one are discussed.
K J Huang, C C Chen, Y Y Chang
openaire   +1 more source

Acoustical Control of External Gear Pumps by Intensity Measuring Techniques

Noise Control Engineering Journal, 1990
The increasing use of external gear pumps in hydraulic applications makes noise a critical problem. In this viw it is very importanto to make available measurement and analysis techniques able to evaluate each design option in terms of cost to benefit ratio, enhancing the product optimization.
CARLETTI E, VECCHI I
openaire   +1 more source

The Theoretical Flow Ripple of an External Gear Pump

Journal of Dynamic Systems, Measurement, and Control, 2003
In this paper, the theoretical flow ripple of an external gear pump is studied for pumps of similar size using different numbers of teeth on the driving and driven gears. In this work, the flow ripple equation is derived based upon the flow of incompressible fluid across the changing boundaries of a control volume.
Noah D. Manring, Suresh B. Kasaragadda
openaire   +1 more source

NOISE REDUCTION IN EXTERNAL GEAR PUMP

PAHTEI-Procedings of Azerbaijan High Technical Educational Institutions
External gear pumps are widely employed in various industrial applications due to their simplicity, reliability, and efficiency. However, they often generate considerable noise, which can be a significant concern in noise-sensitive environments.
openaire   +1 more source

External Gear Pump Volumetric Efficiency: Numerical and Experimental Analysis

SAE Technical Paper Series, 2009
<div class="htmlview paragraph">External gear pumps and motors are robust and low cost positive displacement machines and are widely used in industrial and mobile applications. Nowadays however, optimal global efficiency represents a more crucial aspect to be considered when designing a hydraulic machine.
BORGHI, Massimo, ZARDIN, Barbara, SPECCHIA, EMILIANO   +2 more
openaire   +1 more source

Effect of Nanoscale Additives on External Gear Pump Performance

Volume 1: Symposia, Parts A, B and C, 2009
In this study, the effect of ultrafine graphite and multi-walled carbon nanotube (CNT) additives on the performance of an external gear pump was investigated. Colloidal suspensions of each additive were created in ethanol with concentrations varying from 200 ppm to 1550 ppm, low enough that there was no significant change in the viscosity of the ...
Philip J. Martorana, Ilker S. Bayer, Adam Steele, Eric Loth   +3 more
openaire   +1 more source

New Methods of Reducing Noise in External Gear Pumps

SAE Technical Paper Series, 1980
<div class="htmlview paragraph">The noise from external gear pumps has been significantly reduced by a new design which consists of two sets of gears, half the width of a standard gear, and offset about 1/2 pitch. The new pump makes use of a housing which is externally basically the same as a standard pump.
John Hobbs, Hans-Juergen Fricke
openaire   +1 more source

The Flow Pulsation Analysis of an External Gear Pump

Advanced Materials Research, 2011
In this paper, the theoretical flow ripple of an external gear pump is studied for pumps of similar size using different numbers of teeth on the driving and driven gears. External gear pumps with three different types of tooth profiles are studied. Nondimensional flowrates and fluctuation coefficients of gear pumps are discussed.
Yan Zhi Li, Li Huan Gao, Xiao Yang Tang
openaire   +1 more source

Modeling of high-pressure external gear pump

2011
Hydraulic systems provide good dynamic behaviour and therefore are one of the main design concept for industrial applications, such as the example of drives for machine tools. The most important part of the hydraulic system is the pump. The main task of the pump is the converting mechanical energy from the prime mover into hydraulic energy, or the flow
Barle, Jani, Dobrota, Đorđe, Bilić, Boženko   +2 more
openaire   +1 more source