Results 271 to 280 of about 126,683 (307)

Prediction of Cutting Force When Surface Milling Using Face Milling Tool

2020
The aim of the study is to predict the cutting force when surface milling with a face milling tool. Based on theoretical published research on cutting force modeling, this study predicted the cutting force when milling 40Cr steel with a face milling tool.
Nguyen Van Thien, Do Duc Trung, Vilaivanh Xaixavang, Tran Thi Hong, Nguyen Thanh Tu, Tran Ngoc Giang, Le Xuan Hung   +6 more
openaire   +1 more source

Optimal Design of Face Milling Cutter Geometry

CIRP Annals, 1990
Abstract This paper focuses on the development of the CAMSS Computer Aided Milling System Simulator) that describes the milling operation consisting o structural and cutting dynamic in a closed-loop configuration. The CAMSS incorporates an optimization algorithm to optimize the insert geometry, namely axial and radial rake angles of each insert in a ...
Gim, J.-S, Cho, D.W, Lee, J.M.
openaire   +2 more sources

Cutter Life for Face-Milling Cast Iron

Journal of Fluids Engineering, 1954
Abstract This is a second paper to give the results of a series of tests to face-mill a variety of metals with cutters of various materials. The work was sponsored by the War Production Board under the auspices of the Office of Production Research and Development, through the Manufacturing Engineering Committee of The American Society of
W. W. Gilbert, O. W. Boston, H. J. Siekmann   +2 more
openaire   +1 more source

Eco-friendly face milling of titanium alloy

International Journal of Precision Engineering and Manufacturing, 2014
Recently, a use of difficult to cut materials including titanium alloy has been substantially increasing in aerospace and automotive industries. Eco-friendly machining technology, which eliminates or minimizes cutting fluids in machining fields, has been emerged in compliance with green manufacturing trend.
Kyung-Hee Park, Gi-Dong Yang, Myung-Gyu Lee, Hoon Jeong, Seok-Woo Lee, Dong Yoon Lee   +5 more
openaire   +1 more source

Tool wear monitoring in face milling

2010
The purpose of this thesis is to investigate tool wear monitoring using Fourier Series simulation of steady state cutting forces. These simulations show that mean and fundamental values are all that is required to accurately predict immersion and tool wear (high frequency terms are ignored).
openaire   +1 more source

Neural Network Modeling for Face Milling Operation

International Journal of Vehicle Structures and Systems, 2019
Milling operation is one of the important manufacturing processes in production industry. Study and analysis of milling process parameters such as spindle speed, feed rate and depth of cut are important for process planning engineers. The responses are temperature, surface roughness, machining time, feed force, thrust force and cutting force.
B. Sureshkumar, V. Vijayan, S. Dinesh, K. Rajaguru   +3 more
openaire   +1 more source

Influence of Steel Hardness in Face-Milling

Journal of Fluids Engineering, 1949
Abstract Face-milling tests are reported on seven different kinds of steels for power consumption and tool life at hardnesses of approximately 200, 300, and 400 Bhn. At any given hardness power requirements varied but little, but differences in tool life were considerably greater.
J. B. Armitage, A. O. Schmidt
openaire   +1 more source

Monitoring Face Milling Using Fuzzy Logic

1992
Cutting process monitoring is mainly aimed at preventing undesirable damage to the machining system components caused by the failure of cutting tools. Additionally in order to optimize adaptive control, tool wear and the changes in the process should continuously be sensed.
openaire   +1 more source

Navigating financial toxicity in patients with cancer: A multidisciplinary management approach

Ca-A Cancer Journal for Clinicians, 2022
Grace Li Smith, Matthew P Banegas, Chiara Acquati, Lmsw   +2 more
exaly  

Face à l'imprévisible : mille milliards de scénarios

Le Débat, 1990
  +8 more sources