Results 61 to 70 of about 755,619 (231)
Advanced Engineering Materials, EarlyView.Schematic representation of modes of microcrack nucleation, growth and temporary arrestment at different boundaries, with the criteria for crack propagation in three scenarios: (1) large notch, (2) defect/small sharp notch, and (3) long crack. This work revisits and integrates results on the fatigue behavior of advanced bainitic steels (in particular ...
Lucia Morales‐Rivas
wiley +1 more source
Advanced Engineering Materials, EarlyView.This article investigates the dependence of the properties on the manufacturing orientation in the form of the inclination angle to the build plate of LPBF‐fabricated NiTi rods with a diameter of 150–220 µm. Metallographic, chemical, thermal, and mechanical characterization show behavior under identical manufacturing conditions that ranges from ...
Sandra Herzig +2 more
wiley +1 more source
Blow out fracture A Novel Management Modality [PDF]
, 2013 Blow out fracture of orbit involves fracture of orbital floor without fracture of infraorbital rim. This injury is common from frontal blow to orbit. Frontal blow to orbit causes increased intraorbitaltension causing fracture of floor of the orbit (weak ...
Thaigarajan, Balasubramanian; Stanley Medical College Chennai India +1 more
core
Architecture‐Driven Sensor Stability in Weft‐Knitted Engineering Textiles
Advanced Engineering Materials, EarlyView.Textile‐integrated sensor architectures are systematically compared to evaluate their electromechanical behavior under combined mechanical and environmental loading. Pocket‐based integration exhibits stable and reproducible signals, whereas tunnel‐based routing shows higher sensitivity accompanied by increased variability.
Adnan Maroof Khan +5 more
wiley +1 more source
Entropy‐Driven Design of Low‐Melting‐Point Alloys via Compositionally Complex Strategy
Advanced Engineering Materials, EarlyView.Conventional low‐melting‐point alloys (LMPAs) are limited by a narrow compositional space and inherent property trade‐offs. This review presents an entropy‐driven design strategy that overcomes these limitations, ushering in a new class of low‐melting‐point compositionally complex alloys (LMCCAs).
Yinghui Shang +6 more
wiley +1 more source
Metallurgical aspects of rock bolt environment fracture
, 2005 The aim of this research was to understand the Stress Corrosion Cracking (SCC) of rock bolts. The laboratory tests have produced fracture surfaces similar to those from service.
Villalba, Ernesto +5 more
core
Advanced Engineering Materials, EarlyView.This study examines Invar composites reinforced with titanium carbide (TiC) and titanium nitride (TiN) using laser powder bed fusion (LPBF). It presents the influence of reinforcements on microstructure, tensile properties, and thermal expansion. Results show that TiC effectively strengthens Invar while maintaining low thermal expansion, whereas TiN ...
Ayodeji Nathaniel Oyedeji +3 more
wiley +1 more source
Intratemporal Facial Nerve Paralysis- A Three Year Study
Bengal Journal of Otolaryngology and Head Neck Surgery, 2016 Introduction This study on intratemporal facial paralysis is an attempt to understand the aetiology of facial nerve paralysis, effect of different management protocols and the outcome after long-term follow-up.
Anirban Ghosh +2 more
doaj +3 more sources
Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning
Advanced Engineering Materials, EarlyView.The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley +1 more source