Results 51 to 60 of about 13,695 (264)

Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites

Advanced Engineering Materials, EarlyView.
Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter, Andreas Bezold, Johan Westraadt, Katharina Fiegl, Subham Chattoraj, Benjamin Wahlmann, Carolin Körner, Michael Mills, Mathias Göken, Steffen Neumeier   +9 more
wiley   +1 more source

In Situ Micromechanical Study of Bimodal γ′–γ″ Precipitate Assemblies in Ni–Cr–Al–Nb Superalloy

Advanced Engineering Materials, EarlyView.
A Ni–Cr–Al–Nb superalloy with a bimodal γ′–γ″ precipitate distribution is developed. Composite precipitate assemblies form through heterogeneous nucleation, effectively impeding dislocation motion. Micropillar compression reveals high strength at room and elevated temperatures, governed by precipitate shearing, with coupled faulting mechanisms ...
Ujjval Bansal, Tae‐Hyeok Kang, Pyuck‐Pa Choi, Subin Lee, Christoph Kirchlechner   +4 more
wiley   +1 more source

Microstructure Reconstruction in Battery Electrodes Using Machine Learning Based on Low‐Voltage Focused Ion Beam–Scanning Electron Microscopy Tomography Images

Advanced Engineering Materials, EarlyView.
Low‐voltage FIB‐SEM tomography combined with a image preprocessing pipeline improves phase contrast and enables reliable machine‐learning segmentation of conductive networks in lithium‐ion battery electrodes. Structural descriptors are extracted from segmented images, done semimanually and automated, and compared.
Lisa Beran, Vincent Nebel, Dominik Perius, Kshitij Kumar, Yannis Heim, Laura Bies, Tobias Kraus   +6 more
wiley   +1 more source

Triple Junctions as Dislocation‐Like Defects: The Role of Grain Boundary Crystallography Revealed by Experiment and Atomistic Simulation

Advanced Engineering Materials, EarlyView.
Grain boundary triple junctions are an essential ingredient of the microstructure of polycrystalline materials. In this study, a triple junction is observed using atomic‐resolution scanning transmission electron microscopy and characterized. Computer simulations reveal that the junction has a dislocation character that is determined by the joining ...
Tobias Brink, Saba Saood, Peter Schweizer, Jörg Neugebauer, Gerhard Dehm   +4 more
wiley   +1 more source

Edupreneurship implementation through teaching factory on mechanical engineering competence

Jurnal Pendidikan Vokasi, 2022
This study aims to (1) Describe how the edupreneurship implementation through Teaching Factory (TEFA) on the mechanical engineering expertise competence at SMK Muhammadiyah 1 Sukoharjo; (2) Describe the factors supporting the successful implementation of
Tri Kuat, Purnawan Purnawan
doaj   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Optimization approach for the combined planning and control of an agile assembly system for electric vehicles

Proceedings of the Conference on Production Systems and Logistics, 2020
For some years now, the automotive industry has been challenged by growing market dynamics, shorter product lifecycles and customers' increasing demands for individualization. In order to cope with this development, the automotive assembly needs to adapt
Burggräf, Peter, Dannapfel, Matthias, Adlon, Tobias, Riegauf, Aaron, Schukat, Esben, Schuster, Felix   +5 more
doaj   +1 more source

Critical conditions for factory ramp-up planning in SMEs

Proceedings of the Conference on Production Systems and Logistics, 2023
Companies experiencing rapid sales growth need to ramp-up operations and production facilities to meet the increased customer demand. Exporting small and medium sized companies (SMEs) offering new technology in new markets often have to deal with high ...
Thomassen, Maria, Skjelstad, Lars, Herberger, David, Hübner, Marco, Stich, Volker   +4 more
doaj   +1 more source

Additive Manufacturing of Alumina‐Reinforced Elastomers

Advanced Engineering Materials, EarlyView.
Vat‐photopolymerized elastomers reinforced with platelet‐shaped alumina exhibited preferential orientation, reduced porosity, and significantly enhanced mechanical performance. A 3 wt% platelet loading increased tensile strength from 12.4 to 45.7 MPa, highlighting the critical role of filler morphology in elastomeric VPP composites.
Majid Barzegar Keyvani, Zongwen Fu, Robert Göstl, Hamed Shokri, Carmine Putignano, Gianluca Percoco, Bilal Gökce   +6 more
wiley   +1 more source

Extrusion‐Based Additive Manufacturing of Advanced Ceramics: Strengthening Mechanisms and Process Optimization Review

Advanced Engineering Materials, EarlyView.
This review comprehensively evaluates extrusion‐based additive manufacturing for advanced ceramics, detailing feedstock options and key process parameters. By critically addressing defect mechanisms like porosity and cracking, the work highlights optimization strategies through machine learning and advanced postprocessing.
Meisam Bakhtiari, Mohammad Hadi Sheikh‐Ansari, Avinash Borgaonkar, Mehran Dadkhah, Abdollah Saboori   +4 more
wiley   +1 more source