Results 161 to 170 of about 2,461,573 (347)

A Dislocation Perspective on Strength and Toughness in Ceramics

Advanced Engineering Materials, EarlyView.
Dislocations in ceramics enjoy a long but yet under‐appreciated history. The three research waves for dislocations in ceramics highlight the topic evolution over the last 90 years. This review focuses on the impact of dislocation on strength and toughness in ceramics.
Xufei Fang
wiley   +1 more source

Fault-tolerance in metric dimension of boron nanotubes lattices. [PDF]

Front Comput Neurosci, 2022
Hussain Z, Munir MM.
europepmc   +1 more source

Inverse Identification of Energy‐Dependent Laser Absorptivity in NiTi Laser Powder‐Bed Fusion via Calibrated Melt Pool Simulation

Advanced Engineering Materials, EarlyView.
A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi, Hadi Moutablaleh, Ignatius A. Setiawan, Mehrshad Mehrpouya   +3 more
wiley   +1 more source

Compatibility of Methacrylate Based Resins Controls Interfacial Failure and Toughness in 3D‐Printed Multimaterial Composites

Advanced Engineering Materials, EarlyView.
This work shows that the mechanical performance of multimaterial digital light processing (DLP) printed thermoset composites is governed by resin compatibility and interfacial design rather than spatial patterning alone. Brittle and ductile resin combinations produced premature interfacial failure, while graded interfaces and mechanically compatible ...
Ahmed M. H. Ibrahim, Li Meng, Ahmad R. Najafi, Nicolas J. Alvarez   +3 more
wiley   +1 more source

Software modification aided transient error tolerance for embedded systems

, 2013
Commercial off-the-shelf (COTS) components are increasingly being employed in embedded systems due to their high performance at low cost. With emerging reliability requirements, design of these components using traditional hardware redundancy incur large
Kim Sunesen, Sunesen, Kim, Mathew, J., Pradhan, Dhiraj K., Gerard Rauwerda, Sunesen, K., Ioannis Sourdis, Shafik, Rishad Ahmed, Potman, J., Potman, Jordy, Sourdis, Ioannis, Rishad A. Shafik, Shafik, R.A., Rauwerda, G.K., Jimson Mathew, Pradhan, D.K., Dhiraj K. Pradhan, Mathew, Jimson, Rauwerda, Gerard, Jordy Potman   +19 more
core   +1 more source

Enhanced Practical Byzantine Fault Tolerance via Dynamic Hierarchy Management and Location-Based Clustering. [PDF]

Sensors (Basel), 2023
Kim G, Cho J, Choi M, Kim B.
europepmc   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Fault Tolerance Optimization of a Lithium Battery Pack Having a Damaged Unit. [PDF]

ACS Omega, 2022
Gu F, Chen Z, Wang M, Li Z.
europepmc   +1 more source

Human Gut Bacteria and Lipidic Nanoparticles: Particle Composition Predicts Structural Transformation and Bacterial Biocompatibility

Advanced Functional Materials, EarlyView.
Lipidic nanoparticles (LNPs) were incubated with 21 gut bacteria frequently associated with the human microbiome. SAXS revealed that ∼75% of tested species induced structural transformations in monoolein LNPs, whereas phytantriol and phospholipid formulations remained unaffected.
Jonathan Caukwell, Emily L. Gulliver, Livia Salvati Manni, Frithjof Herb, Caitlin Welsh, Samuel C. Forster, Andrew J. Clulow, Wye‐Khay Fong   +7 more
wiley   +1 more source

Fault Tolerance and Reliability in Scientific Workflows

, 2005
The emerging technologies of web services, agents and service-oriented workflows will enable scientific projects and experiments to be conducted on a larger scale than ever before.
Mouallem, Pierre
core