Results 151 to 160 of about 13,965 (304)

Evaluation of Plasticity and Creep Parameters From Tensile Stress–Strain Data for a Range of Strain Rates

Advanced Engineering Materials, EarlyView.
This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley   +1 more source

Protecting FPGA-Based Cryptohardware Implementations from Fault Attacks Using ADCs. [PDF]

Sensors (Basel)
Potestad-Ordóñez FE, Casado-Galán A, Tena-Sánchez E.   +2 more
europepmc   +1 more source

Influence of Surface Finish on the Tribological Performance of AlTiBN Coatings Deposited on Forming Tools

Advanced Engineering Materials, EarlyView.
Aluminum and nitride coatings are used in industry because they are hard, resist wear, and protect against oxidation. Adding boron can improve friction behavior and other properties. This study tests coatings on surfaces with different finishes. Results show smoother surfaces perform better, while rough ones wear faster, although coatings can reduce ...
Adrián Claver, Iker Alfonso, Eneko Barba, Javier León, José Antonio García, Iñaki Zalakain, Iván Fernández Martínez, Arley García‐Carrero, Christian Almeyda, Daniel Salcedo   +9 more
wiley   +1 more source

State and Fault Estimation for Uncertain Complex Networks Using Binary Encoding Schemes Under Switching Couplings and Deception Attacks. [PDF]

Sensors (Basel)
Hou N, Chang M, Gao H, Hu Z, Bu X.
europepmc   +1 more source

Experimental Characterization and Constitutive Modeling of the Effect of Prior Inelastic Strain on the Viscoplastic Behavior of AD730 at 700 °C

Advanced Engineering Materials, EarlyView.
This study shows that superalloys used in aircraft engine disks become much more prone to deformation at high temperatures if they have been strained during manufacturing. This effect increases with the level of prior strain but eventually reaches a limit.
Fabio Machado Alves da Fonseca, Patrick Villechaise, Malik Durand, Arnaud Longuet, Florent Coudon, Loïc Signor, Julien De Jaeger, Dominique Eyidi, Nathalie Bozzolo, Jonathan Cormier   +9 more
wiley   +1 more source

Lattice-based Fault Attacks against ECMQV [PDF]

ECMQV is a standardized key agreement protocol based on ECC with an additional implicit signature authentication. In this paper we investigate the vulnerability of ECMQV against fault attacks and propose two efficient lattice-based fault attacks.
Linmin Fan, Wenling Wu, Weiqiong Cao, Hua Chen, Jingyi Feng   +4 more
core  

Cyber attack and fault detection in DC microgrids by designing an event-triggered based-robust algorithm. [PDF]

Sci Rep
Hosseini Rostami SM, Pourgholi M, Asharioun H.   +2 more
europepmc   +1 more source

Precipitation Simulations of the O‐Phase in Ti2AlNb Alloys Processed by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
Simulated and experimental evolution of the O‐phase volume fraction during postprocessing of a Ti‐21Al‐25Nb (at.%) alloy processed by laser powder bed fusion. With results of sensitivity to input parameters from a thorough and quantified analysis, the interfacial energy matrix/precipitate is the most relevant input parameter for the simulation of the O‐
Silvana Tumminello, Joachim Gussone, Suzana G. Fries, Marcus Rackel, Andreas Stark, Norbert Schell, Jan Haubrich, Guillermo Requena   +7 more
wiley   +1 more source

A blockchain-enabled framework for secure and efficient data transmission in underwater sensor networks using advanced cryptographic techniques. [PDF]

Sci Rep
Kumar KK, Pavani M, Chandra NS, Chitralingappa P, Kumar BH, Anushree G.   +5 more
europepmc   +1 more source

A Dislocation Perspective on Strength and Toughness in Ceramics

Advanced Engineering Materials, EarlyView.
Dislocations in ceramics enjoy a long but yet under‐appreciated history. The three research waves for dislocations in ceramics highlight the topic evolution over the last 90 years. This review focuses on the impact of dislocation on strength and toughness in ceramics.
Xufei Fang
wiley   +1 more source