Results 181 to 190 of about 11,373,640 (309)

Reliable directional relaying for T-Connected Series-Compensated transmission lines. [PDF]

Sci Rep
Elsadd MA, Adly AR, Elgamasy MM.
europepmc   +1 more source

The Impact of High‐Productivity Processing on the Fatigue Failure of an Additive Manufactured Superalloy HAYNES 282

Advanced Engineering Materials, EarlyView.
The low cycle fatigue life of additive manufactured HAYNES® 282® superalloy was investigated for conventional and high‐productivity processing: samples of the former lasted 1400–1700 cycles, while samples of the latter failed at ~ 1200 cycles, at 760 °C and 1% strain.
Abdul Shaafi Shaikh, Ahmed Fardan, Tatiana Mishurova, Eduard Hryha   +3 more
wiley   +1 more source

Fault analysis and performance improvement of grid-connected doubly fed induction generator through an enhanced crowbar protection scheme. [PDF]

PLoS One
Talani RA, Kaloi GS, Ali A, Abbas G, Emara A, Touti E.   +5 more
europepmc   +1 more source

Laser Powder Bed Fusion of Copper–Tungsten Composites for Heat Sink Applications in High‐Power Electronics

Advanced Engineering Materials, EarlyView.
This article demonstrates the successful qualification of a copper–tungsten composite for laser powder bed fusion. The resulting components exhibited high density, high thermal conductivity, and reduced thermal expansion. Heat sinks with complex geometries were successfully manufactured, clearly showcasing the material's potential for additive ...
Simon Rauh, Shashank Deepak Prabhu, Jannik Huber, Lioba Fischer, Gerhard Wolf, Nico Hempel, Peter Mayr   +6 more
wiley   +1 more source

Hybrid meta heuristic and fuzzy impedance method for fast fault location in power system lines. [PDF]

Sci Rep
Najafzadeh M, Pouladi J, Daghigh A, Beiza J, Abedinzadeh T.   +4 more
europepmc   +1 more source

Effects of Carbon Nanoparticles on Triboelectro‐Induced Surface Defects

Advanced Engineering Materials, EarlyView.
Carbon nanoparticles added to grease modify the electrocontact behavior. The synergy of particle concentration and electric current dominates the surface damage of metals in contact. Electrical surface damage caused by current leakage is a critical challenge in high‐performance applications such as electric vehicle (EV) drivetrains and wind turbine ...
Mohsen Tajedini, Lu Fang, Jacob Bons, Mohammad Humaun Kabir, Evan Johnson, Joe Kosmoski, Hong Liang   +6 more
wiley   +1 more source

Performance evaluation of advanced metaheuristic algorithms for directional overcurrent relay coordination in distribution networks. [PDF]

Sci Rep
Arslanoğlu İ, Altaş İH, Kılıç H.
europepmc   +1 more source

Duplex Stainless Steel Laser‐Surface Textured: Stability in Brine Solution

Advanced Engineering Materials, EarlyView.
Controlled laser‐surface treatment (LST) of duplex DSS2205 steel is performed to increase its stability in brine solution under cyclic electrochemical assays. The superior protection with respect to flat and smooth panels is attributed to the presence of FeCr2O4 as the main protective oxide layer in the LST surface, after corrosion tests. The stability
Mohammad Rezayat, Hamidreza Enshaei, Elaine Armelin, José I. Iribarren, Antonio Mateo, Miguel Morales   +5 more
wiley   +1 more source

Arc Fault Detection for Photovoltaic Systems Using Independent Component Analysis Technique and Dynamic Time-Warping Algorithm. [PDF]

Sensors (Basel)
Xu J, Ding S, Li G, Wang Q.
europepmc   +1 more source