Results 101 to 110 of about 509,267 (235)
Control of Bacterial Attachment on Macroporous PDMS/Paraffin SLIPS With Varying Lubricant Viscosity
Slippery liquid‐infused porous surfaces (SLIPS) prepared from macroporous PDMS, infused with medical‐grade paraffins, were systematically investigated regarding the correlation of viscosity, surface corrugation, bulk porosity, and bacterial resistance. Substrate porosity was found to dominate lubricant stabilization and the antifouling activity.
Regina Kopecz +3 more
wiley +1 more source
Screw fasteners are undoubtedly one of the most important machine elements due to their outstanding characteristic to provide a high clamping force just with a simplified design. However, the loosen vibration is their inherent and inevitable fault.
X. J. Jiang +4 more
doaj +1 more source
High‐aspect‐ratio low‐melting‐point alloy inclusions are embedded within multilayer silicone laminates to create thermally programmable stiffness. Sequential activation of alloy‐rich layers produces four distinct mechanical states and reconfigures tendon‐driven actuator trajectories under the same load.
Palpolage Don Shehan Hiroshan Gunawardane +4 more
wiley +1 more source
Locked and creeping patches along the Hayward Fault, California
The results of mapping locked and unlocked patches on the Hayward fault using the local recurrence time method are compared with models derived from surface creep and geodetic measurements. The data used were the M > 1.0 earthquakes in the USGS catalog since 1981.0, located within 5 km of the fault trace.
openaire +1 more source
Liquid‐Crystal‐Based Reconfigurable Intelligent Surface for 7 GHz Mobile Communication
The glass‐based liquid‐crystal reconfigurable intelligent surface (LC‐RIS) integrates active‐matrix driving and blind‐greedy phase optimization within a 5G‐NR OFDM framework. This enables continuously tunable and autonomous enhancement of wireless coverage. Leveraging the transparency and manufacturability of liquid crystal panels, it is ideally suited
Tien‐Lun Ting +5 more
wiley +1 more source
Locking Status and Earthquake Potential Hazard along the Middle-South Xianshuihe Fault
By combining the seismogenic environment, seismic recurrence periods of strong historical earthquakes, precise locations of small⁻moderate earthquakes, and Coulomb stress changes of moderate⁻strong earthquakes, we analyze the potential ...
Rumeng Guo +4 more
doaj +1 more source
A desktop environment for assessment of fault diagnosis based fault tolerant flight control laws [PDF]
We present a simulation based software environment conceived to allow an easy assessment of fault diagnosis based fault tolerant control techniques. The new tool is primary intended for the development of advanced flight control applications with fault ...
Gertjan Looye +5 more
core +1 more source
3D‐Printed Actuator Powered by Liquid Crystal Elastomer Muscles at the Water–Air Interface
Soft robots for unstructured environments require responsive, durable actuators. Liquid crystal elastomers (LCEs) provide large reversible deformations under thermal or optical stimuli. Direct ink writing enables fabrication of LCE actuators integrated with silicone, with mesogen chemistry and oligomers optimized for printable inks.
Cecilie Ryberg +5 more
wiley +1 more source
Optically pumped magnetometers are employed to contactlessly map the spatiotemporal dynamics of the magnetic field linked to electrical activity of a skeletal muscle in vivo. It is demonstrated that localization of the clinically relevant innervation zone is feasible using this non‐invasive magnetic measurement modality. ABSTRACT Magnetomyography (MMG)
Simon Nordenström +12 more
wiley +1 more source
The Distribution of Interseismic Locking on the Cascadia Subduction Zone Using Bayesian Methods
We use a Bayesian probabilistic framework to invert for the kinematic locking distribution on the Cascadia Subduction Zone, constrained by surface deformation data and a prior assumption of the locking pattern.
Anna Pearson, David Schmidt
doaj +1 more source

