Results 11 to 20 of about 239 (154)
A Comparative Assessment of Chromium-Boron Hardfacing Using SMAW and FCAW Techniques. [PDF]
ScientificWorldJournalThis research paper investigates the effectiveness of shielded metal arc welding (SMAW) and flux‐cored arc welding (FCAW) on mild steel substrates for chromium–boron hardfacing. Chromium–boron alloys are hard‐wearing and corrosion‐resistant materials used in industries where wear resistance is critical.
C CR +6 more
europepmc +3 more sources
Journal of Materials Research and Technology, 2021 Underwater wet flux-cored arc welding (FCAW) process was used to join 2205 duplex stainless steel using Ni-based filler under three different heat inputs of 16.9 kJ/cm, 23.5 kJ/cm and 32 kJ/cm.
Qiang Ma +6 more
doaj +3 more sources
Advances in Materials Science and Engineering, 2018 This study presents the Taguchi design method with L9 orthogonal array which was carried out to optimize the flux-cored arc welding (FCAW) process parameters such as welding current, welding voltage, welding speed, and torch angle with reference to ...
Tianqi Li +3 more
doaj +2 more sources
Process Parameter Effect on Deformation of a V-groove Thin Plate for FCAW and EGW [PDF]
Journal of the Korean Welding and Joining Society, 2013 Abstract Finite element analysis and welding experiments were performed to evaluate deformation aspect for Flux Cored Arc Welding(FCAW) and Electro Gas Welding(EGW). Numerical researches of FCAW and EGW were performed considering the difference of number of welding pass and welding direction to arc flow.
Juho Han +5 more
openaire +3 more sources
Advances in Materials Science and Engineering, Volume 2022, Issue 1, 2022., 2022 The low‐carbon martensitic stainless steel CA6NM is widely used in the impellers of hydroelectric and nuclear power units due to its advantages of high hardness, corrosion fatigue strength, and good fracture toughness. In order to analyze the number of repair welding times on the properties of heat‐affected zone (HAZ, the most unstable area of welded ...
Peng Liu +5 more
wiley +1 more source
Constitutive Model and Fracture Criterion of Q345 Steel Welded Joints
Complexity, Volume 2022, Issue 1, 2022., 2022 Welding joint is a key component in steel structure engineering, which is often subjected to complex stress and becomes the weak link of building structure, and different fracture modes may appear under different stress. In this study, the ductile fracture of Q345 steel welded joint was investigated by selecting the base material and heat‐affected zone
Lian Song +5 more
wiley +1 more source
The comparison of gas tungsten arc welding and flux cored arc welding effects on dual phase steel
Materials Research Express, 2020 This work aims to investigate the effects of two welding techniques (gas tungsten arc welding (GTAW) with filler metal ER70S-3 and flux cored arc welding (FCAW) with filler metal E71T1C) on the microstructure and mechanical properties (including ...
Mahmoud Abbas +2 more
doaj +1 more source
Influence of Cladding Parameters with FCAW on Bead Geometry with Plackett-Burman Experiment Used [PDF]
Archives of Metallurgy and Materials, 2018 The paper analyzes, from the geometrical aspect, the quality of the new flux cored wire intended for cladding process in function of changes in cladding parameters such as welding speed, coefficient of thermal conductivity, power source setting, the ...
R. Bęczkowski
doaj +1 more source
Fatigue assessment of high strength welded joints through the strain energy density method
Fatigue &Fracture of Engineering Materials &Structures, Volume 43, Issue 11, Page 2694-2702, November 2020., 2020 Abstract The main aim of the present work is to investigate, through the strain energy density method, the fatigue behaviour of high strength welded joints realised employed in hydraulic runner blades. The geometries, found in literature, present the welding bead machined in order to have no geometrical discontinuities in the specimen realising a wide ...
Pietro Foti, Filippo Berto
wiley +1 more source
Weld Quality Analysis of High-Hardness Armored Steel in Pulsed Gas Metal Arc Welding
Metals, 2023 As improving fuel economy and performance through weight reduction in vehicles are recognized as important tasks, the defense industry is researching ways to reduce the weight of armor plates for combat vehicles and increase bulletproof performance and ...
Hwi Jun Son +5 more
doaj +1 more source