Results 191 to 200 of about 2,830 (209)

A study of indentation for mechanical characterization of the Fe2B layer

Surface and Coatings Technology, 2013
Abstract In this study, the indentation properties of the Fe2B layer were evaluated. The powder-pack boriding process on low-carbon steels was carried out at a temperature of 1273 K for 4, 6 and 8 h of exposure. First, Vickers indentation testing was performed on the boride layer at a distance of 50 μm from the surface of the borided steel with ...
I. Campos-Silva, E. Hernández-Sánchez, G. Rodríguez-Castro, H. Cimenoglu, J.L. Nava-Sánchez, A. Meneses-Amador, R. Carrera-Espinoza   +6 more
openaire   +1 more source

Nuclear Magnetic Resonance Detection of a Spin-Wave Gap in Fe2B

Journal of Applied Physics, 1969
Measurements of the 11B frequency vs temperature in the ferromagnetic intermetallic Fe2B for 4.2°≤T≤373°K give evidence of a spin-wave gap even in zero applied field. Above about 100°K, the reduced frequency is approximately proportional to T3/2 (with a small admixture of a T5/2 term).
I. D. Weisman, L. J. Swartzendruber, L. H. Bennett   +2 more
openaire   +1 more source

Bulk Fe2B crystal fabricated by mechanical ball milling and plasma activated sintering

Journal of Alloys and Compounds, 2014
Abstract Bulk Fe 2 B crystals were fabricated with Fe and B mixed powders by mechanical ball milling and plasma activated sintering (PAS). The results indicate that, as milling time reaches 10 h and above, the diffraction peaks of B powders will vanish and new phases will not appear.
Zhifu Huang, Shengqiang Ma, Jiandong Xing, Biye Wang   +3 more
openaire   +1 more source

Stacking faults and structural characterization of mechanically alloyed Ni50Cu10(Fe2B)10P30 powders

The European Physical Journal Plus, 2015
The nanocrystalline NiCu(Fe2B)P alloy was prepared by mechanically alloying of the elemental powders in a high-energy ball mill under argon atmosphere. The transformations occurring in the material during milling were studied by X-ray diffraction.
M. Slimi, M. Azabou, L. Escoda, J. J. Suñol, M. Khitouni   +4 more
openaire   +1 more source

???????????? ???????????????????????? ?? ?????????????? ???????????????????? Fe3P???Fe2P???Fe2B

2012
???????????????????? ?????????????????????? ?????????????? ?????????????????????? ?? ?????????????????? ?????????????? ???????????????? ???????????????? ?????????? Fe???P???B ???? ?????????????? 12% P ?? 0???4% B ?? ?????????????????? ???????????????????? ?????????????????????? 10???100 ??/??. ?????????????????????? ???????????? ????????????????????????
openaire   +1 more source

Borlanmış AISI M2 Yüksek Hız Çeliğinde Tek Fazlı (Fe2B) Borür Tabakası Oluşumu

2022
In this study, AISI M2 High-Speed Steel was borided by a pack-boriding method. Samples were borided in the atmospheric controlled furnace at 900 to 1100 C for 2 to 6h. For the boriding heat treatment, AISI 316 stainless steel crucible and a powder mixture with the trade name EKABOR 2 as the boriding agent were used.
AYDOĞMUŞ, Tuna, ÇİÇEK, Bünyamin, TOPUZ, Polat, AYDIN, Özlem   +3 more
openaire   +1 more source

The Phase Fe2B

International Journal of Materials Research, 1987
Eckart Kneller, Yunus Khan
openaire   +1 more source

Microstructure, chemical composition, wear, and corrosion resistance of FeB–Fe2B–Fe3B surface layers produced on Vanadis-6 steel using CO2 laser

International Journal of Advanced Manufacturing Technology, 2017
Aneta Bartkowska, Dariusz Bartkowski, Damian Przestacki   +2 more
exaly  

Growth Kinetics of the Fe2B Layers and Adhesion on Armco Iron Substrate

Journal of Materials Engineering and Performance, 2014
Milton Carlos Elias-Espinosa, Martin Ortiz, J Zuno-Silva   +2 more
exaly  

The tribological properties of bulk Fe2B with pre-oxidation treatment at 750°C in air

Industrial Lubrication and Tribology, 2019
Kemin Li, Zhifu Huang
exaly