Results 41 to 50 of about 5,995,042 (211)
Genetic aspects of feed intake in lactating sows [PDF]
, 2011 Productivity of sows has increased worldwide, especially during the last decade. Sows have been changed genetically to produce larger litters. It was hypothesized that including feed intake or feed efficiency during lactation or both in the breeding ...
Bergsma, R.
core
Influence of cutting parameter on surface quality in dry turning of different materials
Al-Qadisiyah Journal for Engineering Science, 2023 In machining operations, surface roughness (Ra) is an essential measure of product quality. It is determined by the cutting settings. The parameters that have been worked on are the Feed (F) (0.72, 0.88, 0.96, 1.12 mm/min), depth of cut (DOC) (0.5mm ...
Zainab Hussein Mohsein +2 more
doaj +1 more source
Influence of turning cutting parameters on surface deformation of annealed AISI-1020 steel
Revista Facultad de Ingeniería Universidad de AntioquiaThis paper presents a study on the influence of the cutting parameters (depth of cut, feed rate, and cutting speed) of turning with a carbide insert on the plastic deformation induced in annealed AISI-1020 steel.
Omar Zurita +2 more
doaj +1 more source
Passage Rate of Feed in Very Young Chicks
Poultry Science, 1984 White Leghorn chicks were reared on diets in which soybean oil at 4% or corn oil at 5 or 10% was substituted isocalorically for carbohydrate calories. The transit time ( TRT ) of diets was determined in these chicks with ferric oxide as a marker. The average TRT for three experiments was 167 min. Overall, there was no significant effect (P greater than
A, Golian, D, Polin
openaire +2 more sources
Review of SEAFDEC/AQD fish nutrition and feed development research [PDF]
, 1996 Research on fish nutrition and feed development at SEAFDEC Aquaculture Department has focused on three major areas: nutrient requirements and their interrelationships, digestive enzymes and digestibility, and practical feed development for important ...
Millamena, Oseni M.
core +1 more source
Materials Research ExpressAISI 1040 medium-carbon steel offers a favourable combination of strength and toughness but presents notable machinability challenges for manufacturing industries. This study investigates metal turning operations on AISI 1040 using vegetable oil-in-water
Vishal Shenoy P +6 more
doaj +1 more source
Rekayasa MesinThis study examines the effect of spindle speed and feed rate variations on the delamination mechanism and thrust force of hybrid composite materials reinforced with ramie weave and coir fibers.
Sri Chandrabakty +2 more
doaj +1 more source
Discriminating Feed Rate of Combine Harvester by Using Association Rule Mining
Elektronika ir Elektrotechnika, 2023 The feed rate is an important evaluation index of combine harvester performance. The quick identification of the amount of feed rate that enters the combine during harvesting is of great significance for the efficiency and operational quality of the ...
Yehong Liu +4 more
doaj +1 more source
The feed-in tariff in the UK : a case study focus on domestic photovoltaic systems [PDF]
, 2013 This paper explores the photovoltaic (PV) industry in the United Kingdom (UK) as experienced by those who are working with it directly and with consideration of current standards, module efficiencies and future environmental trends.
Kirwan, Kerry +3 more
core +1 more source
Simulation and Experimental Investigation of Electrochemical Mill-grinding of GH4169 Alloy
International Journal of Electrochemical Science, 2018 Electrochemical mill-grinding (ECMG) is a new method of compound machining inspired by numerical-control milling. A simple rodlike grinding wheel that rotates at high speed is used as the cathode and processes the workpiece along a set trajectory ...
Hansong Li +3 more
doaj +1 more source