Results 151 to 160 of about 864,342 (206)
Experimental Investigation on Ferritic Stainless Steel Columns in Fire
Fire Safety Journal, 2013 peer reviewedThis paper presents the performance of EN 1.4003 ferritic stainless steel hollow section columns when exposed to fire loading. Experimental analysis of the behaviour of ferritic stainless steel structural members in fire represents a novelty.
Barbara Rossi +2 more
exaly +2 more sources
Some of the next articles are maybe not open access.
Related searches:
Related searches:
Joining of austenitic stainless steel and ferritic stainless steel to sialon
Journal of Materials Processing Technology, 2001Abstract Joining of ceramics to metal is not easy due to the difference in the thermal expansion of the two materials. In this research work, the joining of sialon to austenitic stainless steel and ferritic stainless steels were compared. At above a joining temperature of 1200°C, sialon will react with steel to form iron silicide and nitrogen is ...
P Hussain, A Isnin
openaire +1 more source
2008
Abstract This chapter discusses the alloy composition, metallurgy, mechanical behavior, stabilization, texture, anisotropy, high-temperature properties, and corrosion and oxidation resistance of ferritic stainless steels.
openaire +1 more source
Abstract This chapter discusses the alloy composition, metallurgy, mechanical behavior, stabilization, texture, anisotropy, high-temperature properties, and corrosion and oxidation resistance of ferritic stainless steels.
openaire +1 more source
Metal Science and Heat Treatment, 1973
Translated from Metalloved. Term. Obrab. Metal.; 15: No. 7, 16-20(Jul 1973). The corrosion resistance of ferritic steels containing N and C and alloyed with Mo was investigated. The corrosion tests were conducted using oxygen-saturated acids and chloride salt solutions. Results are tabulated and discussed. (JRD)
openaire +1 more source
Translated from Metalloved. Term. Obrab. Metal.; 15: No. 7, 16-20(Jul 1973). The corrosion resistance of ferritic steels containing N and C and alloyed with Mo was investigated. The corrosion tests were conducted using oxygen-saturated acids and chloride salt solutions. Results are tabulated and discussed. (JRD)
openaire +1 more source
Dynamic Recrystallization Textures in Ferrite and Ferritic Stainless Steels
Materials Science Forum, 1998The textures produced in two conventional IF steels, two ferritic stainless steels and α-iron were determined after deformation in torsion over the temperature range 20-1200°C. The experiments were carried out in the ferrite range and the conditions were chosen so as to eliminate the possibility of static recrystallization.
J. Baczynski, I. DeArdo, John J. Jonas
openaire +1 more source
Roping phenomena in ferritic stainless steels
Materials Science and Technology, 1986AbstractThe mechanism of roping in two ferritic stainless steels (type 18·2 and type 430) has been studied.
T. Sheppard, P. Richards
openaire +1 more source
Magnetic testing of ferritic stainless steel
AIP Conference Proceedings, 2021Structural changes due to annealing were analyzed on ferritic stainless steel Electrodur EN 1.4105 (AISI 430F) specimens. Changes of magnetic properties and selected parameters of Barkhausen noise were compared to microstructural changes detected by microscopy and Vickers hardness measurement.
Vladimír Jančárik +2 more
openaire +1 more source
Ferritic stainless steel — A coinage material
Bulletin of Materials Science, 1989General economic and metallurgical requirements, and processing methods for coinage materials are reviewed. The Indian effort at the development of ferritic stainless steels for coinage is discussed. The results of several trials at the Salem Steel Plant towards establishing the appropriate composition and processing route are presented and evaluated.
V P Sardana, D A Pikle
openaire +1 more source
Toughness of Ferritic Stainless Steels
1980A comprehensive review of the factors fundamental to ferritic stainless steel toughness has been undertaken. Emphasis has been placed on the micromechanisms of fracture and their effects on the ductile-to-brittle transition consistent with the Cottrell crack nucleation model. The general effects of strain rate, plastic constraint (including gage effect)
openaire +2 more sources
Sintered 434L ferritic stainless steels
Materials & Design, 1985Abstract Stainless steel powder metallurgical parts are increasingly used in automotive, aircraft, business machines, chemical, marine, tools and hardware industries. Although some results on sintered austenitic stainless steels have been reported, there is no information on a relatively cheaper ferritic stainless steel series of alloys.
G.S. Upadhyaya, S.K. Mukherjee
openaire +1 more source