Results 61 to 70 of about 864,342 (206)

Design of High‐Performance MnCo1.5Cu0.5O4 Spinel Contact Material with Optimized Electrical Conductivity and Thermal Stability for Solid Oxide Electrolysis Cells by Cu Doping

ENERGY &ENVIRONMENTAL MATERIALS, Volume 9, Issue 5, September 2026.
Cu‐doped spinel MnCo1.5Cu0.5O4 exhibits excellent conductivity and stability as SOC contact material. After 1000‐h aging at 850 °C, the contact layer maintains a 10 mΩ cm2 ASR value, and a single‐cell stack achieves a H2O/CO2 co‐electrolysis power density of 0.52 W cm−2.
Haozhen Li, Shuai Yuan, Xingtong Mao, Hao Shi, Hengyong Tu, Chao Ma, Lei Zhu, Zhen Huang   +7 more
wiley   +1 more source

Ferritic Stainless Steel Tubular Sections Strengthened with CFRP Plate subjected to Concentrated Interior Bearing Load

, 2013
Web crippling failure of ferritic stainless steel tubular structural members could be found due to localized concentrated loads or reactions. This paper reports an experimental investigation on strengthening of ferritic stainless steel tubular members ...
S. M. Zahurul Islam, Young, B, Islam, SMZ, Ben Young   +3 more
core   +1 more source

Optimization of Material Density and Strength in Super Duplex 2507 Stainless Steel via Selective Laser Melting: CCD‐PSO‐DFA Approach

Engineering Reports, Volume 8, Issue 9, September 2026.
Systematic framework has been established to model, analyze, and optimize the properties of SLM parts. The major results drawn from the proposed work: CCD‐based modeling for density and UTS of SLM‐fabricated SDSS 2507. Scan speed showed the highest influence on density and tensile strength.
Tejas Ranganath, Niranjan Hiremath, Avinash Lakshmikanthan, Chithirai Pon Selvan, Shamanth Vasanth, Manjunath Patel Gowdru Chandrashekarappa, Vijay Desai   +6 more
wiley   +1 more source

On the shear resistance of ferritic stainless steel composite slabs [PDF]

, 2018
Steel-concrete composite floors are commonly used in construction due to their favourable weight-to-depth ratio and erection time. Typically, concrete is poured onto a galvanised steel deck acting as formwork.
Rossi, Barbara, Lauwens, Kathleen, Arrayago Luquin, Itsaso, Mirambell, Enrique, Mirambell Arrizabalaga, Enrique, Arrayago, Itsaso, Fortan, Maarten   +6 more
core   +1 more source

Effect of Substrate Temperature on the Surface of Cathodic Cage Plasma Nitrided Aisi 430 Ferritic Stainless Steel [PDF]

Iranian Journal of Chemistry & Chemical Engineering
The Cathodic Cage Plasma Nitriding (CCPN) system has been widely used as a better and low-cost surface modification technique for stainless steel and other metals. The efficacy of the CCPN system depends upon several control parameters. The effect of the
Muhammad Khalid, Syed Hussain, Muhammad Shafiq, José Ruíz Mondragón, Saad Mehmood, Muhammad Asghar   +5 more
doaj   +1 more source

Experimental and Comparative Study of the Corrosion Behavior of Lean Duplex Stainless Steel in Seawater

Materials and Corrosion, Volume 77, Issue 9, Page 1399-1423, September 2026.
The localized corrosion behavior of lean duplex stainless steel EN 1.4062 is systematically compared with austenitic and higher‐alloyed duplex grades in natural seawater. A clear resistance ranking is established, highlighting EN 1.4062 as a cost‐effective alternative for limited marine exposure.
Mohammad Hassanzadeh, Nicolas Larché, Audrey Allion‐Maurer, Raf Dewil, Barbara Rossi   +4 more
wiley   +1 more source

Application Prospect and Effect of Rare Earth Elements in Ferritic Stainless Steels

Teshugang, 2008
The anti-pitting corrosion,anti-stress corrosion and high temperature anti-oxidizing properties of ferritic stainless steels(11%～30%Cr)are better than that of austenitic stainless,but normal feritic stainless steels have higher ...
李亚波, 王福明, 朱宝晶
doaj  

Computer Modeling of the Ferrite‐To‐Austenite Transformation in a Super‐Duplex Stainless Steel and the Important Role of Trans‐Interface Diffusion

steel research international, Volume 97, Issue 9, Page 4483-4493, September 2026.
An accurate moving boundary model for volume diffusion containing boundary conditions from trans‐interface diffusion (TID) simulates the austenite growth during cooling. TID of Cr, Mo, N and Ni enhance growth kinetics. Without TID, compositions of the interface region change, decreasing the driving force for growth and finally causing numerical ...
A. Salwén, T. Müller, S. Nouhi, J. Y. Jonsson   +3 more
wiley   +1 more source

Progress in Grades and Refining Technology of Ultra Purity Ferritic Stainless Steels

Teshugang, 2006
The(C+N)content in ultra purity ferritic stainless steels is ≤150×10-⁶,its corrosion resistance, weldability and toughness are obviously higher than that of common ferritic stainless steels.
游香米, 姜周华, 李花兵
doaj  

Processing‐Centric Innovative Strategies for Protonic Ceramic Electrochemical Cells

Advanced Energy Materials, Volume 16, Issue 29, 5 August 2026.
This review reveals how processing‐centric fabrication strategies govern architecture, microstructure, and interfaces in protonic ceramic electrochemical cells (PCECs), establishing a framework that translates materials innovation into scalable PCEC technologies.
Dongyeon Kim, Seeun Oh, Hyeonggeun Kim, Hyeongmin Yu, Chuancheng Duan, Kang Taek Lee   +5 more
wiley   +1 more source