Results 21 to 30 of about 10,619 (226)

Effect of Printing Parameters on Dimensional Error, Surface Roughness and Porosity of FFF Printed Parts with Grid Structure

open access: yesPolymers, 2021
Extrusion printing processes allow for manufacturing complex shapes in a relatively cheap way with low-cost machines. The present study analyzes the effect of printing parameters on dimensional error, roughness, and porosity of printed PLA parts obtained
I. Buj-Corral   +2 more
semanticscholar   +1 more source

Fabrication of PLA/PCL/Graphene Nanoplatelet (GNP) Electrically Conductive Circuit Using the Fused Filament Fabrication (FFF) 3D Printing Technique

open access: yesMaterials, 2022
For the purpose of fabricating electrically conductive composites via the fused filament fabrication (FFF) technique whose properties were compared with injection-moulded properties, poly(lactic acid) (PLA) and polycaprolactone (PCL) were mixed with ...
N. Masarra   +6 more
semanticscholar   +1 more source

Aditivna proizvodnja u kemijskom inženjerstvu. Prvi dio: procesi za polimere [PDF]

open access: yesKemija u Industriji
Aditivna proizvodnja, obično poznata kao 3D-ispis, skup je procesa koji stvara objekte dodavanjem materijala izravno iz digitalnih modela. Aditivnom proizvodnjom moguće je izraditi dijelove dodavanjem materijala točno tamo gdje je materijal potreban ...
Domagoj Vrsaljko   +3 more
doaj   +1 more source

Multifunctional performance of carbon nanotubes and graphene nanoplatelets reinforced PEEK composites enabled via FFF additive manufacturing

open access: yesComposites Part B: Engineering, 2020
The study is focused on multifunctional performance of carbon nanotubes (CNT) and Graphene nanoplatelets (GNP) reinforced PEEK composites enabled via fused filament fabrication (FFF) additive manufacturing (AM) utilizing in-house nanoengineered filaments.
M. F. Arif   +5 more
semanticscholar   +1 more source

Improvement of the layer-layer adhesion in FFF 3D printed PEEK/carbon fibre composites

open access: yes, 2021
Improvement of the mechanical properties of FFF 3D printed CF/PEEK composites was achieved by printing under favorable crystallization conditions. It was possible to improve the layer-layer tensile strength more than fivefold from 6.96 MPa to 36.28 MPa ...
K. Rodzeń   +4 more
semanticscholar   +1 more source

The application of fibular free flap with flexor hallucis longus in maxilla or mandible extensive defect: a comparison study with conventional flap

open access: yesWorld Journal of Surgical Oncology, 2018
Background The repair and reconstruction of maxillary and mandibular extensive defects have put huge challenges to surgeons. The fibular free flap (FFF) is one of the standard treatment choices for reconstruction.
Youkang Ni   +9 more
doaj   +1 more source

Prevalence and Related Factors of Flexible Flatfoot in School-Aged Children: A Cross-Sectional Study

open access: yesFoot & Ankle Orthopaedics, 2020
Category: Other; Midfoot/Forefoot Introduction/Purpose: There is a greater prevalence of flexible flatfoot (FFF) among children; however, most of them are physiological, and the associated factors are still in debate.
Liang Xiaojun MD, Zhao Hong-Mou MD, PhD
doaj   +1 more source

Impact of Some Overseas Monetary Variables on Indonesia: SVAR Approach

open access: yesECONOMICS, 2017
This study aims to investigate how the influence of monetary variables from abroad to Indonesia’s monetary conditions. This study uses exchange rate variables, interest rates of U.S. central banks, world oil prices and interest rates of Indonesian banks.
Subagyo Ahmad, Witjaksono Armanto
doaj   +1 more source

Filament‐Based Melt Electrowriting Enables Dual‐Mode Additive Manufacturing for Multiscale Constructs

open access: yesSmall Science, 2023
Melt electrowriting (MEW) is an electric‐field‐assisted fiber‐forming biofabrication strategy for the additive manufacturing (AM) of precisely defined 3D microarchitectures.
Kilian Maria Arthur Mueller   +7 more
doaj   +1 more source

Infill Density Influence on Mechanical and Thermal Properties of Short Carbon Fiber-Reinforced Polyamide Composites Manufactured by FFF Process

open access: yesMaterials, 2022
In three-dimensional (3D) printing, one of the main parameters influencing the properties of 3D-printed materials is the infill density (ID). This paper presents the influence of ID on the microstructure, mechanical, and thermal properties of carbon ...
L. Chicoş   +6 more
semanticscholar   +1 more source

Home - About - Disclaimer - Privacy