Results 51 to 60 of about 194,174 (266)

Effectiveness of rTMS on Working Memory and Inhibitory Impairments in Patients With Post‐Stroke Executive Deficits

Annals of Clinical and Translational Neurology, EarlyView.
ABSTRACT Objective Considerable efforts have been dedicated to developing effective treatments for post‐stroke executive impairment (PSEI), among which repetitive transcranial magnetic stimulation (rTMS) has shown great potential. This study aimed to investigate the therapeutic effects of high‐frequency rTMS on working memory (WM) and response ...
Mengting Lao, Rongwei Du, Zhujun Wang, Yang Gao, Meiling Cheng, Xianglong Wang, Wen Wu   +6 more
wiley   +1 more source

Problems of the process of moistening raw cotton and cotton fiber. Cotton fiber wetting process problems

Системный анализ и прикладная информатика
The moistening of raw cotton and cotton fiber is a critical stage in the textile production process, significantly influencing the quality of the final product. However, achieving optimal moisture content presents numerous challenges.
Z. U. Ortiqov
doaj   +1 more source

Early Clinical, Imaging, and Pathological Characteristics of SRPK3/TTN‐Digenic Myopathy

Annals of Clinical and Translational Neurology, EarlyView.
ABSTRACT Objective SRPK3/TTN‐digenic myopathy was recently established as a skeletal muscle myopathy caused by digenic inheritance. This study characterizes the early clinical presentation of SRPK3/TTN‐digenic myopathy in one previously reported and seven newly identified pediatric patients.
Rotem Orbach, Sandra Donkervoort, Carola Hedberg‐Oldfors, Giovanni Baranello, Dimah Saade, Precilla D'Souza, Ruchee Patel, Eva Michael, A. Reghan Foley, Diana Bharucha‐Goebel, S. Jin Haugland, Meghan McAnally, Omer Abdul Hamid, Katherine Chao, Ellen F. Macnamara, Alan H. Beggs, Anna Sarkozy, Juliane Mueller, Steven A. Moore, Richard S. Finkel, Cynthia J. Tifft, Francesco Muntoni, Anders Oldfors, Carsten G. Bönnemann   +23 more
wiley   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

Study on mechanical properties and strength relation between cube and cylinder specimens of steel fiber reinforced concrete

Advances in Mechanical Engineering, 2019
An experimental study was performed on the splitting tensile strength of steel fiber reinforced concrete using cube and cylinder specimens. Effects of volume fraction, aspect ratio, geometry, and tensile strength of steel fiber on the splitting tensile ...
Haitang Zhu, Chuanchuan Li, Danying Gao, Lin Yang, Shengzhao Cheng   +4 more
doaj   +1 more source

Fine-grained concrete with various types of fibers

Инженерно-строительный журнал, 2020
This paper investigates the strength properties of the fine-grained concrete reinforced with the amorphous fiber based on the Fe-B-C system and obtained by the "spinning" method, and concretes reinforced with commercially available types of fibers: fiber
Yasmin Begich, Sergey Klyuev, Vladislav Jos, Artemiy Cherkashin   +3 more
doaj   +1 more source

A Numerical–Experimental Approach for Multi‐Matrix Fiber‐Reinforced Plastics Characterization Using Finite Element Model Updating

Advanced Engineering Materials, EarlyView.
A numerical–experimental framework is developed for characterizing multi‐matrix fiber‐reinforced polymers (MM‐FRPs) combining epoxy and polyurethane matrices. Harmonic bending tests are integrated with finite element model updating (FEMU) to simultaneously identify elastic and viscoelastic material parameters.
Rodrigo M. Dartora, Tales V. Lisbôa, Axel Spickenheuer, Rogério J. Marczak, Jakson M. Vassoler   +4 more
wiley   +1 more source

Effect of fiber length on mechanical properties of wood composite plastic (Polypropylene) [PDF]

تحقیقات علوم چوب و کاغذ ایران, 2010
The objective of adding reinforcing fillers, such as natural fibers to plastics is to increase the strength compared with neat plastic and wood. In this research the effect of wood pulp fiber length (short, medium and long), aspect ratio and fiber ...
Farshid Basiji, Vahid reza Safdari, Ahmad Jahan latibari, Amir Nourbakhsh   +3 more
doaj   +1 more source

Thermomechanical Fatigue and Creep–Fatigue Interaction of Inconel 718 Additively Manufactured by Laser Beam Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth, Tomáš Babinský, Jan Lars Riedel, Wen Hao Kan, Aijun Huang, Martin Heilmaier, Ivo Šulák   +6 more
wiley   +1 more source

Mechanical Properties of Fiber-Reinforced Soil under Triaxial Compression and Parameter Determination Based on the Duncan-Chang Model

Applied Sciences, 2020
To study the mechanical properties of Y-shaped polypropylene fiber-reinforced subgrade fill, the strength characteristics of fiber-reinforced soil with different fiber contents, fiber lengths, and confining pressures were investigated through triaxial ...
Yingying Zhao, Xianzhang Ling, Weigong Gong, Peng Li, Guoyu Li, Lina Wang   +5 more
doaj   +1 more source