Results 111 to 120 of about 248,878 (317)
Advanced Engineering Materials, EarlyView.A numerical–experimental framework is developed for characterizing multi‐matrix fiber‐reinforced polymers (MM‐FRPs) combining epoxy and polyurethane matrices. Harmonic bending tests are integrated with finite element model updating (FEMU) to simultaneously identify elastic and viscoelastic material parameters.
Rodrigo M. Dartora +4 more
wiley +1 more source
Impact resistance of concrete using dovetailed fibres and type 2 synthetic fibres
, 2015 This paper investigates the relative performance of new dovetailed (DT) cross section fibres with regard to impact resistance and energy absorption of concrete.
Richardson, Alan, Batey, David
core
Natural fibres for geotextiles
, 2012 Natural fibre-based geotextiles can compete with polymeric geotextiles on both technical and economic grounds. However, to increase their competitiveness, new areas of application must be developed, with the biggest market share concentrated in three ...
Cherian, B. M. [UNESP] +5 more
core +1 more source
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
The development and properties of glass-ceramic fibres [PDF]
Fibres were produced from glasses with the following compositions: A= 25% Li20 74% SiO2 1% P205 B= 29% LiO2 68% SiO2 1% P205 1% ZnO 1% K20 by drawing the fibres from a single tip platinum bushing.
Jones, R. W.
core
Near‐Field Electrospinning Micro‐Printhead Achieves Precise Control of Nanofiber Deposition
Advanced Engineering Materials, EarlyView.A micro‐printhead for near‐field electrospinning enables reproducible deposition of polymer nanofibers with diameters below 50 nm. Systematic parameter studies uncover the mechanisms linking operating conditions to fiber morphology, paving the way for precise and low‐cost nanoscale 3D manufacturing.As a high‐resolution, cost‐effective, and rapid ...
Han Xu, Dario Mager, Jan G. Korvink
wiley +1 more source
Advanced Engineering Materials, EarlyView.Selenium was incorporated into a sol–gel‐derived bioactive glass to enable sustained therapeutic ion release. The selenium‐containing glass preserved bioactivity while selectively inducing cytotoxicity in osteosarcoma cells and maintaining osteoblastic viability.
Breno Rocha Barrioni +7 more
wiley +1 more source
Identification of cellulosic fibres by FTIR spectroscopy: Thread and single fibre analysis by attenuated total reflectance [PDF]
, 2003 The ability to accurately identify fibres is of importance to conservators, allowing the most appropriate methods of treatment to be employed.
Garside, Paul, Wyeth, Paul
core
Radiation sensitivity of plastic optical fibres
, 2022 Plastic optical fibres were improved considerably during the last few years. It was investigated whether polymethyl methacrylate (PMMA) and polycarbonate (PC) fibres would also be suited for radiation environments.
Schmidt, Hans Ulrich, Köhn, Otmar
core
Advanced Engineering Materials, EarlyView.Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov +4 more
wiley +1 more source