Film Cooling Effectiveness Data for Simple Injection Geometries: A Collection of Three-Axis Plots
International Journal of Rotating Machinery, 1994 A three-axis plot of laterally averaged film cooling effectiveness versus blowing rate and versus dimensionless distance downstream is a sufficiently compact representation of film cooling effectiveness data for injection through a row of holes or two ...
L. D. Stone, R. J. Goldstein
doaj +1 more source
Heat-Transfer Characteristics of Partially Film Cooled Plug Nozzle on a J-85 Afterburning Turbojet Engine [PDF]
Plug nozzle film cooling data were obtained downstream of a slot located at 42 percent of the total plug length on a J-85 engine. Film cooling reduced the aft end wall temperature as much as 150 K, reduced total pressure loss in the upstream convection ...
Nosek, S. M., Straight, D. M.
core +1 more source
Tailoring Functional Properties of Ti–Ni–Cu Shape Memory Alloy Thin Films for MEMS Actuators
Advanced Engineering Materials, EarlyView.A comprehensive study of critical parameters required to develop well‐performing Ti–Ni–Cu thin film shape memory alloy microactuators is provided. Materials science and device integration aspects are integrated by addressing structural and physical relationships using complementary characterization techniques as well as a practical fabrication solution
Elaheh Akbarnejad +6 more
wiley +1 more source
Film-cooling effectiveness with developing coolant flow through straight and curved tubular passages [PDF]
The data were obtained with an apparatus designed to determine the influence of tubular coolant passage curvature on film-cooling performance while simulating the developing flow entrance conditions more representative of cooled turbine blade.
Graham, R. W. +2 more
core +1 more source
Turbulent mixing film cooling correlation [PDF]
, 1972 Film cooling effectiveness correlation predicts air flow requirement for cooling gas turbine combustors. Turbulent mixing model accounts for mixing rate between cooling film and hot gas stream.
Juhasz, A. J., Marek, C. J.
core +1 more source
Enhanced Strength and Corrosion Resistance of Ti‐13Nb‐12Ta‐10Zr‐4Sn Alloy by Aging Treatment
Advanced Engineering Materials, EarlyView.This work systematically investigates the effect of aging treatment on mechanical properties and corrosion behavior of vacuum arc‐melted Ti‐13Nb‐12Ta‐10Zr‐4Sn alloy. Owing to the increased α″ martensite, strength and corrosion resistance were significantly enhanced by aging treatment.
Yuhua Li +5 more
wiley +1 more source
Research On Maximizing Critical And Reducing Initial Heat Flux Densities To Eliminate Any Film Boiling And Minimize Distortion During Quenching [PDF]
, 2017 In the paper the results of testing three types of FUCHS oils: Thermisol QH 120, Thermisol QH 10 and Thermisol QB 46 are discussed. The main attention is paid to critical heat flux densities evaluation because they create a basis for optimizing cooling ...
Dobryvechir, V. (Volodymyr) +3 more
core +2 more sources
Bioinspired Shape‐Memory Hook Fasteners With Programmable Interlocking and Silent Release
Advanced Engineering Materials, EarlyView.Bioinspired hook fasteners made from epoxy shape‐memory polymers are shown to switch between strong, secure attachment and gentle, silent release when heated. By combining programmable geometry and material response, these adaptive fasteners outperform commercial systems in strength and noise control, enabling new solutions for robotics, medical ...
Maria I. Vallejo Ciro +3 more
wiley +1 more source
Experimental flow coefficients of a full-coverage film-cooled-vane chamber [PDF]
Ambient- and elevated-temperature flow tests were performed on a four-times-actual-size model of an impingement- and film-cooled segment of a core engine turbine vane.
Hippensteele, S. A., Meitner, P. L.
core +1 more source
Advanced Engineering Materials, EarlyView.Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir +5 more
wiley +1 more source