Results 41 to 50 of about 357,157 (220)
Advanced Science, EarlyView.We present a complete T2T genome assembly for a key bat reservoir. Integrating population genomics, comparative genomics, transcriptomics, single‐cell omics, and functional assays, we resolve previously inaccessible genomic regions and identify evolutionary signatures associated with immune adaptation.
Yuting Wang +15 more
wiley +1 more source
Metals, 2019 In this work, the analysis of the cutting speed and feed rate influence on tool wear and cutting forces in Ti6Al4V alloy dry machining is presented. The study has been focused on the machining in a transient state.
Yezika Sánchez Hernández +3 more
doaj +1 more source
Development of an ANN model for prediction of tool wear in turning EN9 and EN24 steel alloy
Advances in Mechanical Engineering, 2021 An imperative requirement of a modern machining system is to detect tool wear while machining to maintain the surface quality of the product. Vibration signatures emanating during machining with a single point cutting tool have proven to be good ...
Rahmath Ulla Baig +4 more
doaj +1 more source
Analytical model of progression of flank wear land width in drilling
, 2019 In multipoint operations like drilling, cutting velocities and cutting-edge geometries vary along cutting lips so is the rate of progression of flank wear. Analytical evaluation of flank wear land width in the case of complex tools has received a limited
Barshilia, Harish C, Joshi, SS, Das, R
core +1 more source
Living Electronics: Microbial Metabolism as Batteries, Resistors, and Capacitors
Advanced Electronic Materials, EarlyView.Three microorganisms are assigned the three elementary roles of a circuit on one sheet of paper. Dormant Bacillus subtilis spores germinate to switch the power source on; a photosynthetic Synechocystis biofilm sets resistance by the color and intensity of light; and a respiring Shewanella oneidensis biofilm stores charge. Together they form a printable
Botian Wang, Ruohan Zhang, Seokheun Choi
wiley +1 more source
, 2018 The present study deals with the influence of the microstructures of two wrought superalloys on the flank wear of uncoated cemented tungsten carbide tools in turning.
Hoier, Philipp +14 more
core +1 more source
Degradation modes and tool wear mechanisms in finish and rough machining of Ti17 Titanium alloy under high-pressure water jet assistance [PDF]
, 2013 This article presents the results of an experimental study on the Ti17 titanium alloy, which was carried out to analyze tool wear and the degradation mechanisms of an uncoated tungsten carbide tool insert. Two machining conditions, roughing and finishing,
GERMAIN, Guénaël +3 more
core +1 more source
Nanocrystalline LCO/LLZO Composite Cathode Films for Solid State Batteries
Advanced Energy Materials, EarlyView.A single precursor solution is solution‐deposited and calcined at only 750°C to yield a dense, nanograined LiCoO2/LLZO composite cathode, in which both phases crystallize independently with minimal interdiffusion. Assembled into all‐solid‐state Li‐metal batteries, the composite delivers 111.7 mAh g−1 initial discharge capacity and retains 93% after 100
Lucie Quincke +8 more
wiley +1 more source
Investigation on tool wear and tool life prediction in micro-milling of Ti-6Al-4V
Nanotechnology and Precision Engineering, 2018 Short tool life and rapid tool wear in micromachining of hard-to-machine materials remain a barrier to the process being economically viable. In this study, standard procedures and conditions set by the ISO for tool life testing in milling were used to ...
Amin Dadgari, Dehong Huo, David Swailes
doaj +1 more source
Advances in Mechanical Engineering, 2021 Tuning the parameters of Computerized Numerical Control (CNC) is essential for practical manufacturers. Well configured parameters ensure the efficiency of production and the accuracy of the products.
Fei Li, Jun Liu
doaj +1 more source