Results 241 to 250 of about 193,322 (317)

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

Enhanced cell contact and planarian tissue extract increase DNA replication and viability for neoblast cultivation. [PDF]

iScience
Zhang W, Yang L, Li N, Lei K.
europepmc   +1 more source

Carboxylic‐Acid Functionalized Multiwalled Carbon Nanotube‐Alkane‐Based Resistive Temperature Sensor for Cold Chain Applications

Advanced Engineering Materials, EarlyView.
This study presents a reversible temperature sensor with high switching ratio, ∼103. The device is fabricated using PET‐ITO and carbon nanotube dispersions in alkane. Considering its application in cold chain logistics, a proof‐of‐concept with LED is showcased. Thus, a temperature drop below the threshold temperature (crystallization temperature of the
Sunil Kumar Behera, Philippe Marrec, A. Jorge Parola, Madalena Dionísio, Hugo Águas, Andreia F. M. Santos, Hamed Pourkheirollah, Donald Lupo, César A. T. Laia   +8 more
wiley   +1 more source

Comparative boundary-layer analysis of Buongiorno nanofluid flow over flat surfaces: Blasius, Sakiadis, stagnation-point, and stretching-sheet configurations. [PDF]

Discov Nano
Faisal M, Ibrahim W, Badruddin IA, Zedan A.   +3 more
europepmc   +1 more source

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

Biolayer Interferometry (BLI) to Quantify RALF1-Pectin Interactions. [PDF]

Bio Protoc
Lauw S, Barbez E.
europepmc   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

Three-dimensional computed tomography morphometric analysis of lumbar endplates in Chinese young adults. [PDF]

Front Surg
Cui Y, Wang W, Sun X, Zhang H, Yin W, Cui X, Jiao W.   +6 more
europepmc   +1 more source

Experimental study of fluid-thermal-structural interactions in a Mach-10 compression corner using super-ellipse-based photogrammetry. [PDF]

Exp Fluids
Duchene TA, Schöneich AG, Bathel BF, Weisberger JM, Buck GM, Bodony DJ, Laurence SJ.   +6 more
europepmc   +1 more source

Experimental comparative analysis of solar thermal and photovoltaic integrated vapor absorption refrigeration systems for low-GWP sustainable cooling under tropical conditions. [PDF]

Sci Rep
Selvaraj DA, Nadimuthu LPR, Victor K, Al Bustanji S, Panchyk M.   +4 more
europepmc   +1 more source