Results 131 to 140 of about 210,961 (295)

Composition‐Tuned Enhancement of the Anomalous Nernst Effect in FeCo–Pt Thin Films on Rigid and Flexible Substrates

Advanced Engineering Materials, EarlyView.
Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi, Hiroyuki Awano, Kenji Tanabe   +2 more
wiley   +1 more source

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

Advanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm, Lukas Knöchel, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +5 more
wiley   +1 more source

The design of underwater tactile force sensor with differential pressure structure and backpropagation neural network calibration

Measurement + Control
The underwater tactile force measurement was prone to cross-sensitivity, causing the difficulty in distinguishing tactile force signal with the underwater complex environment of water pressure influence.
Jianjun Zhang, Pengyang Han, Qunpo Liu, Shasha Li, Bin Li   +4 more
doaj   +1 more source

Assessing Altered Coating Adhesion on Plasma‐Deoxidized Surfaces Under Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
This study demonstrates the effectiveness of atmospheric pressure plasma pretreatment in modifying silicon and stainless steel surfaces to improve adhesion. Argon‐hydrogen plasma increases surface roughness and improves adhesion strength, whereas pure argon results in smoother surfaces and structural changes.
Selina Raumel, Lara Kuhr, Khemais Barienti, Sebastian Herbst, Florian Nürnberger, Hans Jürgen Maier, Marc C. Wurz   +6 more
wiley   +1 more source

Magentically actuated compressor [PDF]

, 1985
A vibration free fluid compressor particularly adapted for Stirling cycle cryogenic refrigeration apparatus comprises a pair of identical opposing ferromagnetic pistons located in a housing and between a gas spring including a sealed volume of a working ...
Evans, J., Studer, P. A.
core   +1 more source

Productivity‐Driven Optimization of Laser Powder Bed Fusion Parameters for IN718 Superalloy: Process Control, Microstructure, and Mechanical Properties

Advanced Engineering Materials, EarlyView.
This study demonstrates how optimizing laser power, scanning speed, and hatching distance in laser powder bed fusion can boost the productivity of Inconel 718 manufacturing by up to 29% while maintaining mechanical integrity. The work delivers a validated process window and cost–time analysis, offering industry‐ready guidelines for efficient additive ...
Amir Behjat, Guido Barale, John Stavridis, Ehsan Norouzi, Jin‐Yoo Suh, Dong‐Ik Kim, Luca Iuliano, Abdollah Saboori   +7 more
wiley   +1 more source

Generalized Parity-Time Symmetry Condition for Enhanced Sensor Telemetry

, 2018
Wireless sensors based on micro-machined tunable resonators are important in a variety of applications, ranging from medical diagnosis to industrial and environmental monitoring.The sensitivity of these devices is, however, often limited by their low ...
Alù, Andrea, Chen, Pai-Yen, Cheng, Mark, Cui, Qingsong, El-Ganainy, Ramy, Hajizadegan, Mehdi, Sakhdari, Maryam   +6 more
core   +1 more source

Resistance Rapid Heating of Aluminum Coatings in an Extreme High Vacuum–Adequate Atmosphere for Hot Stamping

Advanced Engineering Materials, EarlyView.
The subject of this work is the development of a corrosion‐protective coating on steel sheets for form hardening. Rapid heating in an extreme high vacuum (XHV)‐adequate atmosphere is a useful method to prevent oxidation during alloying of 22MnB5 and aluminum to obtain a metallurgical bonding.
Lorenz Albracht, Alexander Schnettger, Ulrich Holländer, Sven Hübner, Bernd‐Arno Behrens, Hans Jürgen Maier   +5 more
wiley   +1 more source

Exploratory Research on MEMS Technology for Air-Conditioning and Heat-Pumps [PDF]

, 1998
This report details the efforts to exploit micro-electrical-mechanical-systems (MEMS) and micro device technologies to improve control of multi-channel evaporators by reducing maldistribution among channels, and increase capacity and efficiency of ...
Hrnjak, P.S., Leicht, T.M., Shannon, Mark A.   +2 more
core  

Surface Tension Measurement of Ti‐6Al‐4V by Falling Droplet Method in Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
In this article, the temperature‐dependent surface tension of free falling, oscillating Ti‐6Al‐4V droplets is investigated in both argon and monosilane doped, oxygen‐free atmosphere. Droplet temperature and oscillation are captured with one single high‐speed camera, and the surface tension is calculated with Rayleigh's formula.
Johannes May, Finn‐Lennard Janthur, Lena Kreie, Michael Müller, Sarah Seffer, Nick Schwarz, Jörg Hermsdorf, Thomas Hassel, Stefan Kaierle, Ludger Overmeyer   +9 more
wiley   +1 more source