Results 61 to 70 of about 77,091 (266)
Bond–slip Behavior of Fiber-reinforced Polymer/concrete Interface in Single Shear Pull-out and Beam Tests [PDF]
, 2015 It has been assumed that the fiber-reinforced polymer/concrete interface is subjected to in-plane shear condition when intermediate crack debonding failure occurs.
Harries, Kent A. +2 more
core +2 more sources
Beyond Earth: Resilience of Quasi‐2D Perovskite Solar Cells in Space
Advanced Materials, EarlyView.In the article (DOI: 10.1002/adma.202520433), Christoph Putz and co‐workers demonstrate rigid quasi‐2D perovskite solar cells operating in low Earth orbit, delivering stable power for more than 100 days under real‐space conditions. In‐orbit performance is correlated with extensive ground‐based thermal and proton‐irradiation studies on rigid and ...
Christoph Putz +17 more
wiley +1 more source
Advanced Materials, EarlyView.A fully flexible ion‐gel‐gated graphene‐channel transistor driven by a triboelectric nanogenerator enables self‐powered tactile sensing and synaptic learning. Mimicking spike‐rate‐dependent plasticity, the device exhibits frequency‐selective potentiation and depression, supporting rate‐coded neuromorphic computation even under flex.
Hanseong Cho +3 more
wiley +1 more source
Transfer Length of Strands in Prestressed Concrete Piles [PDF]
, 2002 A top bar effect has been identified in prestressed concrete piles. The effect that this top bar effect has on the development of the prestressing strand is investigated. Strand transfer length is found to be proportional to the observed end slip.
Harries, Kent A. +2 more
core +1 more source
Hybrid Magnetoactive Soft Elastomers: Material Development Toward Application in Diaphragm Pumps
Advanced Materials Technologies, EarlyView.Hybrid magnetoactive soft elastomeric membranes are developed by combining two different types of magnetic particles. The membranes exhibit distinct mechanical, magnetic and thermal properties owing to the unique characteristics of the two magnetic particles.
Somashree Mondal +4 more
wiley +1 more source
Kebolehacuanan suntikan logam mikro SS 316L menggunakan bahan pengikat PEG dan PMMA Mohd [PDF]
, 2012 Pengacuanan suntikan logam mikro atau lebih dikenali µMIM merupakan satu proses yang berkesinambungan daripada proses penyuntikan logam. Proses ini menggunakan serbuk logam bersaiz mikro dan mampu menghasilkan produk mikro yang kompleks pada ...
Ibrahim, Mohd Halim Irwan
core
Advanced Materials Technologies, EarlyView.This study formulated a 5Y‐PSZ zirconia paste for extrusion‐based additive manufacturing via direct ink writing, producing dense ceramic structures for dental applications. A colloidal approach with 47 vol% nanometric powder and tailored additives optimized rheology and printability.
Juliana de Freitas Gouveia Silva +5 more
wiley +1 more source
Dyna, 2018 This study focused on the experimental assessment of the behavior of I-shaped steel beams with longitudinal stiffeners under the action of lateral-torsional buckling.
Néstor I. Prado +3 more
doaj +1 more source
Developing people capabilities for the promotion of sustainability in facility management practices [PDF]
, 2015 Sustainability is becoming an integral part of the life-cycle development of built facilities. It is increasingly highlighted during the post construction phase, as facility management personnel can have major influence to the sustainability agenda
Sarpin, Norliana
core +1 more source
Fabrication, Properties, and Applications of Scaffolds for Bone Tissue Regeneration
Advanced Materials Technologies, EarlyView.This review explores cutting‐edge biomaterials and fabrication techniques for scaffolds in bone tissue regeneration. It conducts a critical comparison of various strategies, meticulously analyzes the key contradictions in the field, and outlines an integrated development path spanning from biomaterial selection to clinical application, while ...
Shangsi Chen, Min Wang
wiley +1 more source